+- MetalworkingFun Forum (http://www.metalworkingfun.com)
+-- Forum: Machining (http://www.metalworkingfun.com/forum-5.html)
+--- Forum: General Metalworking Discussion (http://www.metalworkingfun.com/forum-6.html)
+--- Thread: Latest Delivery (/thread-873.html)
Pages:
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
224
225
226
227
RE: Latest Delivery - Vinny - 02-10-2023
I looked at that to and almost bought one. Decided to hold off and maybe make one.
RE: Latest Delivery - EdK - 02-11-2023
(02-10-2023, 08:11 PM)Vinny Wrote: I looked at that to and almost bought one. Decided to hold off and maybe make one.
I had planned on making one also but when this one came up for sale I don't think I could have bought the materials to make one for the same cost.
This one will get used mostly for smaller threads. I'll single point anything greater than 1/4", probably.
Ed
RE: Latest Delivery - EdK - 02-17-2023
A couple of items arrived today. I went with the HF belt sander that also had the disc sander.
Aluminum for a mini pallet for the mill. 1.25" x 4" x 6"
Ed
[attachment=18232] [attachment=18233]
RE: Latest Delivery - Vinny - 02-17-2023
Ed's post reminded me.. I got some aluminum the other day for an upcoming project. I'm making a rotary for doing pens. The pens lay in slots on the table and a stepper will move each pen under the laser to be engraved then on to the next one. This one will have either 20, 24 or 25 slots. Haven't decided yet. I'll do some tests on slot sizes to see what works best, but they'll be tapered, approx 10mm at the surface, 6-7 at the bottom and around 5mm deep. My plate is a 12x12x3/8" that I'll round out to a 12" circle. The other piece is 5x24x1/4" and part of it will be the base for mounting the stepper and support for the plate.
![[Image: aluminum.jpg]](http://metalshop.nobucks.net/pix/aluminum.jpg)
RE: Latest Delivery - EdK - 02-18-2023
The good belts for the grinder arrived today. Unfortunately the wheels on the grinder aren't even close to being round so some work will need to be done before I can use the belt grinder.
Ed
[attachment=18236]
RE: Latest Delivery - Highpower - 02-18-2023
(02-18-2023, 06:03 PM)EdK Wrote: Unfortunately the wheels on the grinder aren't even close to being round so some work will need to be done before I can use the belt grinder.
Ed
At least it's good you will only need to do the fix once. (I hope.)
RE: Latest Delivery - EdK - 02-19-2023
(02-18-2023, 08:04 PM)Highpower Wrote:(02-18-2023, 06:03 PM)EdK Wrote: Unfortunately the wheels on the grinder aren't even close to being round so some work will need to be done before I can use the belt grinder.
Ed
At least it's good you will only need to do the fix once. (I hope.)
I'll try fixing the existing wheels but in the end I may end up making new aluminum wheels for it. Hopefully not.
Ed
RE: Latest Delivery - rleete - 02-19-2023
I just used a scraper and took off the molding seam. They work fine. Never even looked to see if they were round.
RE: Latest Delivery - EdK - 02-19-2023
(02-19-2023, 06:06 AM)rleete Wrote: I just used a scraper and took off the molding seam. They work fine. Never even looked to see if they were round.
Lots of wobble in one of them. It turns out the bearing wasn't pressed in all of the way on one of them and it's at an angle.
Ed
RE: Latest Delivery - Dr Stan - 03-19-2023
[attachment=18257]
As the pic says, 4 in 1 machine. Did not include the TIG torch which is on order. I have received the argon flow meter and need to get a tank of argon. Will soon be able to build some trusses for a proper roof for the shop.