+- MetalworkingFun Forum (http://www.metalworkingfun.com)
+-- Forum: Machining (http://www.metalworkingfun.com/forum-5.html)
+--- Forum: General Metalworking Discussion (http://www.metalworkingfun.com/forum-6.html)
+--- Thread: Latest Delivery (/thread-873.html)
Pages:
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
224
225
226
227
RE: Latest Delivery - Vinny - 09-08-2022
The set is now complete. 0-12" These last four are 4-5, 5-6, 7-8, 8-9
![[Image: more-mics.jpg]](http://metalshop.nobucks.net/pix/more-mics.jpg)
RE: Latest Delivery - Highpower - 09-08-2022
What?..... you're stopping at 12?
RE: Latest Delivery - Vinny - 09-08-2022
Yep, only planned on 10 but a seller sent the wrong ones then told me to keep em. So I had to go to 12. What else could I possibly do?
RE: Latest Delivery - Vinny - 10-01-2022
Finally found an ER-32 - BS9 collet chuck they didn't want your first born for. It's chinese but has less than a halfathou run out. My DTI was really stiff so I had to use a DI and there was not a lot of movement.
Also in the pic is a coaxial centering bracket less the DTI. I need a new DTI anyway so that's next on the shopping list. It fits with a 5/16 collet and I have one in both BS9 and ER32 so I'm good there.
![[Image: er32-coaxbrac.jpg]](http://metalshop.nobucks.net/pix/er32-coaxbrac.jpg)
RE: Latest Delivery - EdK - 10-01-2022
Nice score!
Ed
RE: Latest Delivery - rleete - 11-08-2022
Got this handed to me after asking questions about a DTI. Toolroom supervisor is my go-to guy for machining questions, and I wanted his opinion on one I found on eBay.
[attachment=18038]
[attachment=18039]
It's an old Mitutoyo, model 513-202. They are selling on eBay for 60 bucks and up, and he wouldn't take any money. I'll make him a pen tonight.
RE: Latest Delivery - TomG - 11-08-2022
(11-08-2022, 01:33 PM)rleete Wrote: Got this handed to me after asking questions about a DTI. Toolroom supervisor is my go-to guy for machining questions, and I wanted his opinion on one I found on eBay.
It's an old Mitutoyo, model 513-202. They are selling on eBay for 60 bucks and up, and he wouldn't take any money. I'll make him a pen tonight.
I had that very same indicator in college.
Tom
RE: Latest Delivery - Dr Stan - 11-08-2022
That is a good one.
RE: Latest Delivery - rleete - 11-11-2022
Bought myself a couple of angle plates. Up until now, I had no good way to machine anything except 90 degrees. Not really a must have item, but I figure I got such a good deal on the DTI that I can afford to splurge a little.
[attachment=18043]
(Stock picture)
RE: Latest Delivery - Dr Stan - 11-12-2022
(11-11-2022, 07:50 PM)rleete Wrote: Bought myself a couple of angle plates. Up until now, I had no good way to machine anything except 90 degrees. Not really a must have item, but I figure I got such a good deal on the DTI that I can afford to splurge a little.
(Stock picture)
Was this also an EBay find? If so can you share the specific seller & item?