+- MetalworkingFun Forum (http://www.metalworkingfun.com)
+-- Forum: Machining (http://www.metalworkingfun.com/forum-5.html)
+--- Forum: How-To's (http://www.metalworkingfun.com/forum-8.html)
+--- Thread: Acme Threads (/thread-868.html)
RE: Acme Threads - TomG - 09-26-2012
Cutting Acme threads is pretty much the same as cutting Unified threads . The only real difference is that the compound is set to 14 1/2º instead of 30º and you can't take as deep a cut because there is more of the tool in contact with the work. If you can cut a Unified thread you can cut an Acme thread, there's nothing magic about it.
Tom
RE: Acme Threads - EdK - 09-27-2012
(09-26-2012, 09:20 PM)TomG Wrote: Cutting Acme threads is pretty much the same as cutting Unified threads . The only real difference is that the compound is set to 14 1/2º instead of 30º and you can't take as deep a cut because there is more of the tool in contact with the work. If you can cut a Unified thread you can cut an Acme thread, there's nothing magic about it.
Tom
I think I've read that with acme threads you feed straight in rather than at an angle like you do with a Unified thread. Is that true?
Ed
RE: Acme Threads - TomG - 09-27-2012
(09-27-2012, 05:53 AM)EdK Wrote:(09-26-2012, 09:20 PM)TomG Wrote: Cutting Acme threads is pretty much the same as cutting Unified threads . The only real difference is that the compound is set to 14 1/2º instead of 30º and you can't take as deep a cut because there is more of the tool in contact with the work. If you can cut a Unified thread you can cut an Acme thread, there's nothing magic about it.
Tom
I think I've read that with acme threads you feed straight in rather than at an angle like you do with a Unified thread. Is that true?
Ed
Nope. The angle of the compound is just different, 14 1/2º instead of 30º. Square threads are fed straight in and those are a pain to cut. Sort of like parting with a twist.
Tom
RE: Acme Threads - EdK - 09-27-2012
(09-27-2012, 06:24 AM)TomG Wrote: Nope. The angle of the compound is just different, 14 1/2º instead of 30º. Square threads are fed straight in and those are a pain to cut. Sort of like parting with a twist.
Tom
Yea, I can see where square threads would definitely need to be fed straight in.
Hmmm, this talk about acme threads reminds me I have a project that is going to need an acme thread cut. I need to make a tailstock to use with my spin indexer for supporting work between centers. It probably doesn't need to be an acme thread but it'll be a good opportunity to get some experience in cutting them.
Thanks,
Ed
RE: Acme Threads - stevec - 09-27-2012
Ed, remember the nut that will follow.
It can be done though, I cut a new nut for the cross feed screw on my 12x36, came out pretty good ( it's left hand too).
RE: Acme Threads - EdK - 09-27-2012
(09-27-2012, 06:50 AM)stevec Wrote: Ed, remember the nut that will follow.
It can be done though, I cut a new nut for the cross feed screw on my 12x36, came out pretty good ( it's left hand too).
Good point Steve. The nut would be the challenge compared to the screw. I'll have to think about that one.
Ed
RE: Acme Threads - Highpower - 09-27-2012
Another possible option - just FYI.
Making Acetal leadscrew nuts the easy way - by Evan Williams
RE: Acme Threads - TomG - 09-27-2012
If the nut is large enough to get a decent size boring bar through, it won't be too bad. If not, you could always make the nut out of bronze and make a tap out of the screw. Real Acme taps are available as well, but VERY pricey.
Tom
RE: Acme Threads - stevec - 09-27-2012
If, your making a screw Ed, make it a bit longer and leave enough slightly oversize Like skip the final cut and you'll have the makings of a tap.
RE: Acme Threads - EdK - 09-27-2012
(09-27-2012, 08:48 AM)stevec Wrote: If, your making a screw Ed, make it a bit longer and leave enough slightly oversize Like skip the final cut and you'll have the makings of a tap.
That's certainly an option. Thanks.
I think I can weasel my way out of this though. I believe I have a piece of 1/2-10 left hand acme at home that I can use for the screw. That doesn't solve my nut problem
though. I also have matching left hand acme nuts that I might be able to turn down and make a press fit into the sleeve. I'll have to start a thread about that project once I get to it.Sorry to David for hijacking his thread. Shame on me!
Ed