+- MetalworkingFun Forum (http://www.metalworkingfun.com)
+-- Forum: Machining (http://www.metalworkingfun.com/forum-5.html)
+--- Forum: How-To's (http://www.metalworkingfun.com/forum-8.html)
+--- Thread: How to Mill a Pocket on the Vertical Milling Machine (/thread-546.html)
RE: How to Mill a Pocket on the Vertical Milling Machine - krv3000 - 06-24-2012
a nuther good post
RE: How to Mill a Pocket on the Vertical Milling Machine - EdK - 06-24-2012
Anybody else have the audio cut out on them when watching this video? It cuts out at about 1:30 and comes back at about 2:50 and then cuts out again at some point that I don't recall.
Ed
RE: How to Mill a Pocket on the Vertical Milling Machine - TomG - 06-24-2012
(06-24-2012, 10:50 AM)EdAK Wrote: Anybody else have the audio cut out on them when watching this video? It cuts out at about 1:30 and comes back at about 2:50 and then cuts out again at some point that I don't recall.
Ed
Seems to be good from my end Ed. Have you checked the batteries in your hearing aid lately?
RE: How to Mill a Pocket on the Vertical Milling Machine - DaveH - 06-24-2012
(06-24-2012, 10:50 AM)EdAK Wrote: Anybody else have the audio cut out on them when watching this video? It cuts out at about 1:30 and comes back at about 2:50 and then cuts out again at some point that I don't recall.
Ed
No, it is fine for me Ed, you must have gone deaf (temporally)
DaveH
RE: How to Mill a Pocket on the Vertical Milling Machine - stevec - 06-24-2012
(06-24-2012, 10:50 AM)EdAK Wrote: Anybody else have the audio cut out on them when watching this video? It cuts out at about 1:30 and comes back at about 2:50 and then cuts out again at some point that I don't recall.Ed, if you think you're shabbily treated, all I got was this
Ed
"embedding disabled by request
Watch on YouTube" .
I did route it through You Tube but when I saw it was 9+ mins.
I got impatient and gave up.
RE: How to Mill a Pocket on the Vertical Milling Machine - ETC57 - 06-24-2012
Thanks Tom,
Very helpful!
Jerry.
RE: How to Mill a Pocket on the Vertical Milling Machine - EdK - 06-24-2012
(06-24-2012, 11:48 AM)TomG Wrote:(06-24-2012, 10:50 AM)EdAK Wrote: Anybody else have the audio cut out on them when watching this video? It cuts out at about 1:30 and comes back at about 2:50 and then cuts out again at some point that I don't recall.
Ed
Seems to be good from my end Ed. Have you checked the batteries in your hearing aid lately?
Ah, maybe that's it. I'll put some new batteries in and see if that helps.
When I watched it I chose the highest resolution. I'll go back and watch it again but leave the resolutions on the default and see if I still have the problem.
Update: OK, the problem only appears if you select one of the HD resolutions, even with new batteries in the hearing aid. All other resolutions seem to play with no lose of audio.
Ed
RE: How to Mill a Pocket on the Vertical Milling Machine - TOM REED - 06-25-2012
How about a vid on making a three eighths or half square recess in the end of a pin to turn with either a chuck key or a ratchet tom
RE: How to Mill a Pocket on the Vertical Milling Machine - TomG - 06-25-2012
(06-25-2012, 10:45 AM)TOM REED Wrote: How about a vid on making a three eighths or half square recess in the end of a pin to turn with either a chuck key or a ratchet tom
Hey Tom,
I think we can solve that problem without the need for a video. Why not just weld or solver solder a 3/8" or 1/2" drive socket to the end of the pin? If that doesn't float your boat, just mill a square pocket in the end of the pin and pick the radii out of the corners with a slotting tool like I did in my Steven's build thread.
Tom
RE: How to Mill a Pocket on the Vertical Milling Machine - TOM REED - 06-25-2012
http://www.homemodelenginemachinist.com/index.php?topic=5495.0 This is the project I want to build and would like to make my own locking pins for the DI chuck 3 of them and would just like to be able to say I built the whole thing pins locks etc without welding, and a small radius in the corner of the pocket would be fine. tom