+- MetalworkingFun Forum (http://www.metalworkingfun.com)
+-- Forum: Machining (http://www.metalworkingfun.com/forum-5.html)
+--- Forum: General Metalworking Discussion (http://www.metalworkingfun.com/forum-6.html)
+--- Thread: Latest Delivery (/thread-873.html)
Pages:
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
224
225
226
227
RE: Latest Delivery - TomG - 04-09-2022
(04-09-2022, 10:11 AM)EdK Wrote:(04-09-2022, 10:08 AM)TomG Wrote: Not sure how hard the steel is, but maybe it could be pinned.
Tom
I was thinking of drilling it at the seam and pinning it with a threaded pin so it could be pulled out if needed. Then the two could be separated if needed.
Ed
If you go with a threaded pin, a pipe plug may be in order, so there is no play. They are available down to 1/16" NPT.
Tom
RE: Latest Delivery - EdK - 04-09-2022
(04-09-2022, 10:18 AM)TomG Wrote:(04-09-2022, 10:11 AM)EdK Wrote:(04-09-2022, 10:08 AM)TomG Wrote: Not sure how hard the steel is, but maybe it could be pinned.
Tom
I was thinking of drilling it at the seam and pinning it with a threaded pin so it could be pulled out if needed. Then the two could be separated if needed.
Ed
If you go with a threaded pin, a pipe plug may be in order, so there is no play. They are available down to 1/16" NPT.
Tom
I meant an internal thread in the pin. Smooth outer surface. They call them "Pull-Out Dowel Pins" on McMaster's web site.
Ed
RE: Latest Delivery - vtsteam - 04-09-2022
Willie, I think I will permanently secure them together. I thought about welding or brazing, but I don't want to heat.
The Loctite appealed to me -- seemed like a good and neat one. I have some Loctite 620 for bearing retention and steam crankshaft building. Seems like that would hold permanently -- the threads are pretty fine and it's a big area.
But Ed if you pin yours successfully, I might follow suit.
RE: Latest Delivery - Highpower - 04-09-2022
(04-09-2022, 10:07 AM)EdK Wrote:(04-09-2022, 09:56 AM)Highpower Wrote: a diamond grinding wheel is my friend when it comes to getting a sharp cutting edge on those import brazed carbide cutting tools
What diamond grinding wheel do you have?
Ed
This is the one I have been using for quite awhile now. I finish up by polishing the surfaces on my home made lapping machine using 5 micron diamond paste, but straight off the grinder will still work too.
[attachment=17844]
[attachment=17845]
I am going to refine things a bit more since I bought a couple of massive 10" diamond wheels (360 and 600 grit) for my Tormek as well. Not something I would recommend to others though unless you enjoy being poor.
RE: Latest Delivery - vtsteam - 04-09-2022
Well, also, even though I said I didn't want to make tools for it, after thinking about it for a bit, one could make a single left hand boring bar that would cover a reasonable range of bore diameters.
The horizontal socket is a through hole, unlike the vertical position socket. That's why I guess they provide so many vertical boring bars in a kit.
And it's not that hard to make a single left handed boring bar using an indexable insert -- seems like a single bar would cover the full range of reasonable stick out diameters.
And the advantage would be you don't have to remember to run in reverse (not that I would ever do that!)
RE: Latest Delivery - Highpower - 04-09-2022
(04-09-2022, 11:01 AM)vtsteam Wrote: And the advantage would be you don't have to remember to run in reverse (not that I would ever do that!)
Starting the mill in the wrong direction? Yeah, I'm glad I don't make those kind of mistakes.
[attachment=17846]
RE: Latest Delivery - Highpower - 04-09-2022
(04-09-2022, 10:31 AM)vtsteam Wrote: Willie, I think I will permanently secure them together. I thought about welding or brazing, but I don't want to heat.
The Loctite appealed to me -- seemed like a good and neat one. I have some Loctite 620 for bearing retention and steam crankshaft building. Seems like that would hold permanently -- the threads are pretty fine and it's a big area.
I wouldn't especially be fond of heat myself either. I would guess there is about a 90% chance of the sleeve retainer compound alone being successful, barring any heavy cuts or snags. When I built one of my competition uppers for high power matches I didn't want to drill into the Krieger stainless barrel (stress changes) to use the standard taper pins for attaching the front sight base. I glued it on with 609 sleeve retainer instead. It has not moved one iota from it's fixed position ever since. Still, I would want a couple of pins in a boring head situation serving as a mechanical backup all the same since it has some horsepower behind it.
RE: Latest Delivery - vtsteam - 04-09-2022
How about the combo of Loctite alone AND running in reverse. Just speaking hypothetically, of course?
The "make a boring bar" is looking like the most straightforward (so to speak) solution for me. It involves using the boring head the way it was meant to be used -- a concept I'm just starting to think about adopting.
RE: Latest Delivery - Highpower - 04-09-2022
(04-09-2022, 12:26 PM)vtsteam Wrote: How about the combo of Loctite alone AND running in reverse. Just speaking hypothetically, of course?
The "make a boring bar" is looking like the most straightforward (so to speak) solution for me. It involves using the boring head the way it was meant to be used -- a concept I'm just starting to think about adopting.
That is what I meant - running in reverse. With light cuts I would guess you might have a 90% chance of it working if using sleeve retainer alone. Again that is just a GUESS on my part. I could be wrong. I've never tried it myself. When I installed the sight base on my barrel I let it cure for about a week. I tested it's strength by wailing on the base with a rubber mallet and a plastic dead blow mallet to see if it would move. Not even a fraction of an inch which is what impressed the heck out of me.
I do agree making your own or purchasing an index-able LH bar would be the best way to go though. I should do the same myself actually.
RE: Latest Delivery - vtsteam - 04-09-2022
Willie 20 years ago I bought a used Cuyuna ULII-02 ultralight plane engine, and needed to change the engine's steel cog belt drive pulley. Couldn't get the old one off even with a puller. I left the puller on stressed up as much as I dared. I'd douse it with WD-40, tap around it with a soft hammer every day. Didn't want to heat it.
Eventually I was dousing and banging on it once a week. Then after a time occasionally whenever I remembered. It lived in the basement. Five months later it let go with a loud pop, heard all the way upstairs, the pulley and puller had flown off and landed on the floor.
The reason it was so tough? Loctite in the taper bore, I discovered.