+- MetalworkingFun Forum (http://www.metalworkingfun.com)
+-- Forum: Machining (http://www.metalworkingfun.com/forum-5.html)
+--- Forum: General Metalworking Discussion (http://www.metalworkingfun.com/forum-6.html)
+--- Thread: Latest Delivery (/thread-873.html)
Pages:
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
224
225
226
227
RE: Latest Delivery - Vinny - 04-11-2020
I bought my press a few years ago for this purpose but never bought the rest of the stuff I needed. While I wanted something a little wider, this will handle most of what I need to do.
![[Image: pbrake.jpg]](http://metalshop.nobucks.net/pix/pbrake.jpg)
RE: Latest Delivery - Hawkeye - 04-12-2020
I made one like that some years ago. Only 9 1/2", but it sure comes in handy when you need to bend something hefty.
RE: Latest Delivery - Vinny - 04-23-2020
When I got my mill, it came with some endmill holders (B&S 9). Missing were 3/4 and 1". It also came with a 3/4 adapter for the 1-1/4 holder so that temporarily solved that problem. I'm making a mount for my mobile antenna, the temporary one I used was just that, temporary. This time around I planned on doing it right.
One of the things I needed was a 2-1/8" milling cutter. I eventually found one on ebay but I needed an arbor. So I made one of them out of a piece of 1" stainless I had (got a bunch of cheap drops from Speedy last year). Problem was, you guessed it, 1" arbor - I still don't have a 1" holder. I was able to find a sleeve to go from 1" to 1-1/4" but that just didn't hold it right and after the first try cutting the rounded end opening for the antenna I was certain it wasn't going to work.
I had one bookmarked on ebay so I looked at it and it was Travers that was selling it. Same price on their website so I went for the free shipping on ebay (plus I get ebay bucks - kinda like cash back).
So the first pic is the new holder, still in the bag, the second pic is the holder, in the mill, with the aforementioned arbor and milling cutter.
![[Image: endmill-holder.jpg]](http://metalshop.nobucks.net/pix/endmill-holder.jpg)
![[Image: endmill-holder2.jpg]](http://metalshop.nobucks.net/pix/endmill-holder2.jpg)
RE: Latest Delivery - Vinny - 04-23-2020
That brake works too good! I also understand why Tarheel uses stainless steel for their mounts. 1/8" aluminum doesn't bend well.
![[Image: mount-dead.jpg]](http://metalshop.nobucks.net/pix/mount-dead.jpg)
RE: Latest Delivery - Dr Stan - 04-23-2020
Some aluminum is quite bendable. Other not so much. For an example look at a soda or beer can. Starts out as a flat sheet , ends up as a can that can hold a liquid under pressure.
RE: Latest Delivery - awemawson - 04-24-2020
Might need annealing before bending if in the hard state.
RE: Latest Delivery - rleete - 04-24-2020
6061 will work harden with a sharp bend like that. Cracking is inevitable. Use a larger bend radius, or different grade.
RE: Latest Delivery - TomG - 04-24-2020
Any aluminum will bend Vinny, you just have to provide a large enough radius on the dies. Your 1/8" tempered aluminum will require at least a 3/16"R.
Tom
RE: Latest Delivery - Hawkeye - 04-24-2020
I got a bunch of aircraft aluminum sheet off-cuts from a friend in the industry. He knew all the numbers and their properties. Tried bending some pieces - they snapped. My friend told me that that grade needed to be annealed - heated to just below melting point, then quenched. After that, you have 25 minutes to do whatever you need to do. Then it hardens again. Pretty cool stuff.
RE: Latest Delivery - Dr Stan - 06-14-2020
![[Image: s-l1600.jpg]](https://i.ebayimg.com/images/g/zrsAAOSworhbxTUn/s-l1600.jpg)
$248.03 including sales tax and shipping. Received an offer from the seller for 5% off plus shipping. Counter offered 10% off including shipping which he accepted. 8" jaw width and will be used on my new to me horizontal mill. Really didn't need it yet, but the offer was too good to pass up. Shipping weight was 111lbs or 50.4 kg. Haven't had the time to inspect it, but I strongly suspect it will more than meet my needs. Will certainly make machining an arbor support much easier. Got to get busy designing one which I'll fab up from aluminum and insert a bronze bushing. BTW, this is the seller's photo. Mine is sitting on the base of the mill.
I'm also going to buy one of these:
![[Image: image_22955.jpg]](https://shop.harborfreight.com/media/catalog/product/cache/1/image/9df78eab33525d08d6e5fb8d27136e95/i/m/image_22955.jpg)
and mount it on top of the ram so I can load/unload the vice and the vertical attachment and reduce the strain on my back. May get a second one for mounting the 12" chuck on my lathe. It too is a beast.