MetalworkingFun Forum
Todays Project - What did you do today? - Printable Version

+- MetalworkingFun Forum (http://www.metalworkingfun.com)
+-- Forum: Machining (http://www.metalworkingfun.com/forum-5.html)
+--- Forum: Projects (http://www.metalworkingfun.com/forum-7.html)
+--- Thread: Todays Project - What did you do today? (/thread-727.html)

Pages: 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 218 219 220 221 222 223 224 225 226 227 228 229 230 231 232 233 234 235 236 237 238 239 240 241 242 243 244 245 246 247 248 249 250 251 252 253 254 255 256 257 258 259 260 261 262 263 264 265 266 267 268 269 270 271 272 273 274 275 276 277 278 279 280 281 282 283 284 285 286 287 288 289 290 291 292 293 294 295 296 297 298 299 300 301 302 303 304 305 306 307 308 309 310 311 312 313 314 315 316 317 318 319 320 321 322 323 324 325 326 327 328 329 330 331 332 333 334 335 336 337 338 339 340 341 342 343 344 345 346 347 348 349 350 351 352 353 354 355 356 357 358 359 360 361 362 363 364 365 366 367 368 369 370 371 372 373 374 375 376 377 378 379 380 381 382 383 384 385 386 387 388 389 390 391 392 393 394 395 396 397 398 399 400 401 402 403 404 405 406 407 408 409 410 411 412 413 414 415 416 417 418 419 420 421 422 423 424 425 426 427 428 429 430 431 432 433 434 435 436 437 438 439 440 441 442 443 444 445 446 447 448 449 450 451 452 453 454 455 456 457 458 459 460 461 462 463 464 465 466 467 468 469 470 471 472 473 474 475 476 477 478 479 480 481 482 483 484 485 486 487 488 489 490 491 492 493 494 495 496 497 498 499 500 501 502 503 504 505 506 507 508 509 510 511 512 513 514 515 516 517 518 519 520 521 522 523 524 525 526 527 528 529 530 531 532 533 534 535 536 537 538 539 540 541 542 543 544 545 546 547 548 549 550 551 552

RE: Todays Project - What did you do today? - f350ca - 11-25-2013

(11-25-2013, 07:47 AM)TomG Wrote: I'll bet it's nice and hot, being that fresh. Thumbsup

Tom

The taste test says HOT but last years batch had my eyes watering steady, would have to step back every so often as I tried to peel it, this year not so bad.

RE: Todays Project - What did you do today? - dallen - 11-28-2013

made this today
[Image: leadscrew-casting-00001.jpg]

replacement for one of the aluminum parts I've made for the shaper, some are going to get replaced with ones made with Cast Iron.

RE: Todays Project - What did you do today? - f350ca - 11-28-2013

I started building larger guards for a 6 inch grinder to use some 7 inch wheels I was given. Here is a roller I built a few years ago rolling the rings for the guards. I've rolled 5/16 plate the full width of the machine, think its 13 inches wide

[Image: IMG_0883.jpg]

RE: Todays Project - What did you do today? - stevec - 11-29-2013

Greg, how many passes does it take to roll the 5/16" plate?
No wonder you have arms like the HULK Rotfl.

RE: Todays Project - What did you do today? - f350ca - 11-29-2013

The "Hulk" ya right, remember, I'm the skinny one who builds machinery to do the work, thank god for hydraulics.
Can't remember how many passes to bend this, would guess 10 or 12, the limiting factor is the pressure screws, when your turning them down the plate is being bent between the two lower rollers, as your rolling it there seams to be more mechanical advantage, maybe just the length of the crank arm.

[Image: IMGP1255.jpg]

Had to cut the plate into three strips to roll it then weld it back together to form the bucket of this tree spade.

[Image: IMGP1258.jpg]

[Image: IMGP1277.jpg]

RE: Todays Project - What did you do today? - awemawson - 11-29-2013

Erected a 4 metre high lamp post using chemical anchor bolts, dug a trench to it, made off both ends of SWA cable, back filled trench placing bricks over cable and also a length of 'warning electric cables below' tape, gingerly climbed the ladder to place the copper lantern on (good stuff this chemical anchor resin :) ) tested and connected up. Now maybe I won't miss the path and end up in the bushes in the dark!.

Then noticed light bulb was wonky tilting one way - oh yes said wife I noticed that when you were up the ladder - didn't want to bother you Yikes

Got out ladder again and sorted it!

Andrew

RE: Todays Project - What did you do today? - ScrapMetal - 11-29-2013

Finished this up yesterday (the wife went to some relatives, I went to the shop).

[Image: binomount01.JPG]

[Image: binomount02.JPG]

It's an adapter so that my son can mount his new 70mm 500x binoculars to a tripod. Just in time for comet viewing. Cool

I used a block of 6061 aluminum for the main body and "naval" brass for the internal shaft. The brass shaft has a "step" built in to it so that no matter how tightly it is made to the tripod mount, it can't pull through. I turned the shaft on the lathe then bored out the body of the adapter for a tight fit. I used my 12-ton hydraulic press to seat the rod in the body then milled it flush.

I learned a number of "lessons" on this little project. Blush When I have the time I'll write up just what they were.

-Ron

RE: Todays Project - What did you do today? - Mayhem - 11-30-2013

I started cleaning up the workshop and decided to add some extra "frame work" to my mig welder to make like a little easier. The 3 phase power lead is now coiled at the back to stop it getting caught up with the torch and earth which hang on a hook on the right. It also makes finding my grips, clamps and magnets easier. Now I just have to round some of the stray clamps up. I need to add another clamp bar for vise-grips and a plate on the front for the larger magnets. Six screws and the frame lifts off. the back is open, so changing bottles is easy.

[attachment=7329]
[attachment=7330]
[attachment=7331]

RE: Todays Project - What did you do today? - f350ca - 11-30-2013

Finished the new larger guards today. I've been using white aluminum oxide wheels for years, thinking they kept the material being ground cooler, then after watching Tom's sharpening tutorial it dawned on me anything I sharpen in the machine shop is HSS and there's no need to keep it that cool. These wheels stay true and will keep a sharp corner for forming split point drills. The cabinet shop requires the aluminum oxide as most of my chisels and plane irons are high carbon steel which are heat sensitive.
These wheels are Norton marked fine and 60/80 grit, even the 60/80 is pretty fine, had to go back to the rough grinder to form a shaper tool then finish it on this grinder.

[Image: IMG_0887.jpg]

RE: Todays Project - What did you do today? - EdK - 11-30-2013

Nice tables on that grinder Greg.

Ed