Building The Steven's Favorite

Building The Steven's Favorite - Printable Version

+- MetalworkingFun Forum (http://www.metalworkingfun.com)
+-- Forum: Machining (http://www.metalworkingfun.com/forum-5.html)
+--- Forum: Gunsmithing (http://www.metalworkingfun.com/forum-27.html)
+--- Thread: Building The Steven's Favorite (/thread-506.html)

Pages: 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27

RE: Building The Steven's Favorite - DaveH - 09-27-2012

(09-27-2012, 09:08 AM)Highpower Wrote: The only problem with the brass tipped screws is that the dog points are awfully small. I'm thinking of making some larger brass "buttons" that will slip over the ends of the screws to get more contact area.
Any thoughts guys?

Hi Willie,
My thought is larger brass "buttons" won't necessarily increase the contact area especially on rounds Smile

DaveH

RE: Building The Steven's Favorite - EdK - 09-27-2012

(09-27-2012, 02:33 PM)DaveH Wrote: Hi Willie,
My thought is larger brass "buttons" won't necessarily increase the contact area especially on rounds

DaveH

That's a good point Dave. Unless you're working with stock with very large diameters larger buttons wouldn't do much good, I would think.

I just drew it up in CAD to see at what point the 3/16" diameter brass point on the set screw would be fully against the stock. At 25" it still did not completely contact the brass point. I think we are good with the brass tipped set screws.

Ed

RE: Building The Steven's Favorite - Highpower - 09-27-2012

(09-27-2012, 02:33 PM)DaveH Wrote: Hi Willie,
My thought is larger brass "buttons" won't necessarily increase the contact area especially on rounds

DaveH

Excellent point Dave. Smile

Now that you've said that, when I think about the contact area in the center of my chuck jaws - they aren't much wider. Chin

And now that the "CAD wizard" has confirmed it, I guess I can assume that 1-1/2" stock will be securely held. Big Grin

Thanks gents.

RE: Building The Steven's Favorite - EdK - 09-28-2012

(09-27-2012, 11:32 PM)Highpower Wrote: And now that the "CAD wizard" has confirmed it, I guess I can assume that 1-1/2" stock will be securely held.

Well, I guess I'm good for something so maybe I'll stick around. Big Grin

RE: Building The Steven's Favorite - Highpower - 09-28-2012

(09-28-2012, 06:02 AM)EdK Wrote: Well, I guess I'm good for something so maybe I'll stick around.

Ed

So, how are you with schematics? Chin

(Hint, hint, wink, wink, nudge, nudge.)

Rotfl

RE: Building The Steven's Favorite - EdK - 09-28-2012

(09-28-2012, 01:14 PM)Highpower Wrote:
(09-28-2012, 06:02 AM)EdK Wrote: Well, I guess I'm good for something so maybe I'll stick around.

Ed

So, how are you with schematics? (Hint, hint, wink, wink, nudge, nudge.)

I'm in electronics for a living so if I suck at schematics then I'm in big trouble. I still have a job so I'm probably doing adequate with schematics. I'm assuming you're talking about electronic schematics.

Ed

RE: Building The Steven's Favorite - Highpower - 09-28-2012

(09-28-2012, 01:18 PM)EdK Wrote: I'm assuming you're talking about electronic schematics.

Ed

Yes, I am. PM inbound..... Big Grin

RE: Building The Steven's Favorite - TomG - 09-30-2012

Today I was working on a method of holding the gun drill in my lathe. Since the drill is actually longer than the lathe I decided that rather than hold the drill with the 3/4" shank, I would hold it in the middle with the boring bar holder. This required a special adapter (of course) to hold the funky shaped drill shank without crushing it. The adapter consists of a 3/4" piece of round with a 3/16" groove in it that has a radius in the bottom to match the drill shank. A 3/16" rectangular bar with a 120º included angle goes in the slot to clamp on the drill and a couple of collars with cap screws provides the clamping force. With this set-up I should be able to grip the drill close to the end of the barrel so I won't need to make a steady brace to support the center, although some sort of support will still be needed on the end of the drill where the coolant hoses attach.

Tom

[Image: 003_13.JPG]

RE: Building The Steven's Favorite - SnailPowered - 09-30-2012

That is a really cool fancy drill holder you have there! I like it!! Thumbsup

RE: Building The Steven's Favorite - DaveH - 09-30-2012

Tom,
A clever idea Worthy

DaveH