Press brake for 20 ton hydraulic press

Press brake for 20 ton hydraulic press - Printable Version

+- MetalworkingFun Forum (http://www.metalworkingfun.com)
+-- Forum: Machining (http://www.metalworkingfun.com/forum-5.html)
+--- Forum: Projects (http://www.metalworkingfun.com/forum-7.html)
+--- Thread: Press brake for 20 ton hydraulic press (/thread-2127.html)

Pages: 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23

RE: Press brake for 20 ton hydraulic press - EdK - 06-29-2014

(06-29-2014, 10:18 AM)DaveH Wrote: ...
Ed, Willie, can you please say how long your guide bushes are. I'm thinking they are 3" long,

DaveH

Good guess Dave. 3.22".

Ed

RE: Press brake for 20 ton hydraulic press - Highpower - 06-29-2014

(06-29-2014, 10:11 AM)DaveH Wrote: Thanks Willie,
Welded it - not a pretty site , I'll clean them up then they won't look too bad

DaveH

Before you make them pretty Dave, I would consider grinding off that center bead on the right side and give it a "do-over". Other than that I think you are good to go without seeing the other side. Thumbsup

I'm assuming your are going to mill off the excess from the bottom of the guides? Just be careful of those weld beads because they are probably going to be in carbide or grinding wheel territory in terms of hardness. Yikes

It won't be long now, and you'll be doing your signature dance again. Smiley-dancenana

RE: Press brake for 20 ton hydraulic press - Highpower - 06-29-2014

By the way Dave, I just noticed where your natural panache comes from. Cool

I see you buy it in bucket loads... Rotfl

RE: Press brake for 20 ton hydraulic press - DaveH - 06-29-2014

(06-29-2014, 11:47 AM)Highpower Wrote: By the way Dave, I just noticed where your natural panache comes from.
I see you buy it in bucket loads...

Now that is good Thumbsup

The right hand side middle weld I can grind it off and re-weld it.

3.22" = near enough 82 mm. Mine are 80mm, now if I put an inverted angle iron in the bottom part (the 'V' die) I should be okay. I'll have to check it out just to make sure.

DaveH

RE: Press brake for 20 ton hydraulic press - DaveH - 06-29-2014

I shall grind all the welds down a bit, make it look a bit more presentable. Depending on how they appear and how I feel I may well fill in the remaining gaps.

DaveH

RE: Press brake for 20 ton hydraulic press - stevec - 06-29-2014

Dave, I'd say weld between the welds that you've already done, chip off the slag, then clean everything up with the grinder and then do a nice slow pass moving the rod from side to side in a zig zag fashion then chip off the slag and you should have a nice wide bead or at least some meat you can regrind to make it look more presentable, if that's what you desire.

RE: Press brake for 20 ton hydraulic press - DaveH - 06-29-2014

Thanks Steve,
Doing a slow pass down the whole guide bush probably may just make things worst. I really don't think that would work with my welding skills Bash

Plus I am always concerned getting the whole thing too hot and causing some distortion.

DaveH

RE: Press brake for 20 ton hydraulic press - stevec - 06-30-2014

Wuss! Rotfl

RE: Press brake for 20 ton hydraulic press - DaveH - 06-30-2014

Rotfl

DaveH

RE: Press brake for 20 ton hydraulic press - ETC57 - 06-30-2014

Ya know I've never been afraid of screwing up the weld, it's having to re machine the parts I worry about.
I enjoy machining just hate do overs. Slaphead

Jerry