+- MetalworkingFun Forum (http://www.metalworkingfun.com)
+-- Forum: Machining (http://www.metalworkingfun.com/forum-5.html)
+--- Forum: General Metalworking Discussion (http://www.metalworkingfun.com/forum-6.html)
+--- Thread: Latest Delivery (/thread-873.html)
Pages:
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
224
225
226
227
RE: Latest Delivery - SteveG - 02-13-2018
I've got one the same style, and pretty sure mine are also Drillpro inserts.
Only used it a couple of times when I've needed to face up to a shoulder (normally use my good facemill), but one of those times was taking a couple of mm off a real Sandvik toolholder and it worked REALLY well. Cut beautifully, and almost a mirror finish :)
Steve
RE: Latest Delivery - Vinny - 03-05-2018
This one will suit me a bit better than the Mitutoyo I have.
![[Image: dro.jpg]](http://metalshop.nobucks.net/pix/dro.jpg)
RE: Latest Delivery - Dr Stan - 05-12-2018
[attachment=15736]
[attachment=15737]
[attachment=15738]
New to me grinder
RE: Latest Delivery - Vinny - 05-12-2018
Must be hard to use side ways like that. Was it hard to mount to the wall or haven't you done that yet?
RE: Latest Delivery - Dr Stan - 05-12-2018
I edited the pics to rotate them, but for unknown reasons they wouldn't stay. Also had them visible instead of clicking on a link. Also didn't stay.
RE: Latest Delivery - Highpower - 05-12-2018
Probably due to the fact that the picture files are HUGE. Try resizing them to about 1/3 of their current size. The page size shown for your pdf's is 45" X 33".
RE: Latest Delivery - Dr Stan - 05-14-2018
well I'm going to have to look for some different software.
RE: Latest Delivery - Highpower - 05-14-2018
Stan, just lower the resolution setting on your camera so that it saves your pictures in a smaller file size. 1024 x 768 is plenty big enough for most purposes. It won't cost you a dime and you won't have to edit them for size after downloading them to your computer.
RE: Latest Delivery - Mike E. - 05-14-2018
This articulated mount arrived today which I found on ebay. It was listed as a " Hydra Clamp ". Its cast iron and well made. I have a couple of small vises on similar bases and thought this could be modified for welding purposes. Turning in the screw hydraulically forces a piston up against the rotating ball to hold it in position. I drilled holes in a 2 1/2" C- clamp and attached it to the threaded arm. Overall, it should be a handy shop item.
RE: Latest Delivery - EdK - 05-14-2018
(05-14-2018, 10:13 AM)Dr Stan Wrote: well I'm going to have to look for some different software.
I use GIMP. It's free and easy to use for scaling pictures.
GIMP
Ed