MetalworkingFun Forum
Todays Project - What did you do today? - Printable Version

+- MetalworkingFun Forum (http://www.metalworkingfun.com)
+-- Forum: Machining (http://www.metalworkingfun.com/forum-5.html)
+--- Forum: Projects (http://www.metalworkingfun.com/forum-7.html)
+--- Thread: Todays Project - What did you do today? (/thread-727.html)

Pages: 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 218 219 220 221 222 223 224 225 226 227 228 229 230 231 232 233 234 235 236 237 238 239 240 241 242 243 244 245 246 247 248 249 250 251 252 253 254 255 256 257 258 259 260 261 262 263 264 265 266 267 268 269 270 271 272 273 274 275 276 277 278 279 280 281 282 283 284 285 286 287 288 289 290 291 292 293 294 295 296 297 298 299 300 301 302 303 304 305 306 307 308 309 310 311 312 313 314 315 316 317 318 319 320 321 322 323 324 325 326 327 328 329 330 331 332 333 334 335 336 337 338 339 340 341 342 343 344 345 346 347 348 349 350 351 352 353 354 355 356 357 358 359 360 361 362 363 364 365 366 367 368 369 370 371 372 373 374 375 376 377 378 379 380 381 382 383 384 385 386 387 388 389 390 391 392 393 394 395 396 397 398 399 400 401 402 403 404 405 406 407 408 409 410 411 412 413 414 415 416 417 418 419 420 421 422 423 424 425 426 427 428 429 430 431 432 433 434 435 436 437 438 439 440 441 442 443 444 445 446 447 448 449 450 451 452 453 454 455 456 457 458 459 460 461 462 463 464 465 466 467 468 469 470 471 472 473 474 475 476 477 478 479 480 481 482 483 484 485 486 487 488 489 490 491 492 493 494 495 496 497 498 499 500 501 502 503 504 505 506 507 508 509 510 511 512 513 514 515 516 517 518 519 520 521 522 523 524 525 526 527 528 529 530 531 532 533 534 535 536 537 538 539 540 541 542 543 544 545 546 547 548 549 550 551 552

RE: Todays Project - What did you do today? - Mayhem - 06-29-2013

So what's it for?

RE: Todays Project - What did you do today? - Hawkeye - 06-29-2013

Last weekend, I dropped into my favourite tool store to see what I could use my birthday gift card on. Nothing I needed, but I saw a 20-ton shop press that was covered in "Does not work" stickers. Regular $400 on for $150 - no warranty, as is.
[attachment=5573]

It's hard to resist an orphan, especially when it involves a challenge. The list included a ram that would not retract (Fred had pumped it down with a 10-ton pump from a porta-power set) and a pump that did NOT work.

The ram was relatively easy - the internal tension spring wasn't attached at the top end. Poor design, poorly executed. They aren't known for full retraction, but will pull up from the work when the pressure is released. Good enough for me.

The pump was another story. On the inlet from the reservoir, the steel ball check valve was above both the tank hole and the hole running to the piston chamber. Nothing to stop the oil from getting pushed back into the tank when the handle is brought down. I drilled the hole for the ball down between the two holes and set the ball with a punch.

There was no check valve after the piston chamber, so the oil came back as soon as the handle was raised for the next stroke. The passage wasn't even machined to take one.I drilled down to allow a 1/4" ball to be added, with a spring between that ball and the ball valve for the pressure release screw. That allowed me to get some movement out of the ram, but not enough to be useful.

Today, a morning thunder storm convinced me to stay in the shop and replace the pressure release valve and final check valve with larger ones. I used a 1/2"-20 bolt for the new valve shaft and a 7/16" ball for the release seal. The old 5/16" ball from the release valve became the new pump check valve. Here's the old shaft beside the new one (installed).
[attachment=5574]

I had to do some tweaking, but ended up getting nearly 15 tons out of it. At that point, the high-pressure bypass valve opens. If I really need the whole 20 tons, I'll fine-tune the HP valve. For now, it has a LOT more power than my 3-ton arbor press. Definitely left an impression on a piece of birch plywood. BTW, the hose clamp on the ram was so I could keep track of movement, when there wasn't much to see.
[attachment=5575]

RE: Todays Project - What did you do today? - Highpower - 06-29-2013

(06-29-2013, 08:43 PM)TomG Wrote: I used a piece of drill rod and turned the taper leaving a temporary full diameter section on the end. Then I grabbed it in the mill vise and milled the tapered section exactly to center to create a cutting edge, removed the temporary end and ground a little relief on the end so it would cut as well.

Tom

Tom, could you post a pic of the flip side of the reamer showing the relief you ground? 17428

RE: Todays Project - What did you do today? - TomG - 06-29-2013

Willie,

You are looking at the relief. This type of reamer is commonly used in watch and clock making. All they are is a pin (tapered in this case) with half of it cut away to the centerline, to create sort of a half moon shape. As long as the cut away part is exactly on center, they will cut and make a very round, very precise hole. A lot of guys use this technique to make chamber reamers, because they are so easy to make.

Tom

[Image: 080.JPG]

RE: Todays Project - What did you do today? - TomG - 06-29-2013

Darren,

This fixture will be used to modify a fine point Sharpie which will in turn be used with one of our instruments, an incubator based microscope called IncuCyte Zoom to mark areas of interest on the bottom of a microplate. This isn't one of my projects, so other than designing and making any required fixturing I'm not really up on all the technical details, but that's basically what it will be used for. I'll post some pics of the fixture when it's finished next week.

Tom

RE: Todays Project - What did you do today? - Mayhem - 06-29-2013

Thanks Tom. I was curious as to the hand wheel, as if the sharpie is on the centreline, turning the hand wheel wouldn't actually do anything. Slightly off centre would produce a nice little circle though.

RE: Todays Project - What did you do today? - TomG - 06-29-2013

Darren,

The fixture is to modify the Sharpie. It will cut it to length, thread the end of it, trim the wick to length and drive a set screw into the cut end to seal it. Once the Pen is modified, it will be used to mark microplates. The modified Sharpie is the end product.

Tom

RE: Todays Project - What did you do today? - Highpower - 06-30-2013

(06-29-2013, 08:43 PM)TomG Wrote: ...and ground a little relief on the end so it would cut as well.

Tom

It's a "D" reamer right? I was just wondering what kind of relief you put on the end of the reamer? 45° chamfer? Full width or half width? (So this half-wit can understand?) Big Grin

RE: Todays Project - What did you do today? - f350ca - 07-04-2013

FINALLY got around to finishing my firewood. 29 here today so it was a chore
Got a record breaking (and back breaking) load this year, measures out at 32 1/2 cord, almost 11 bush cord in Steve's terms.

[Image: IMG_0662%2520copy.jpg]
This plus another four cords that wouldn't fit at the end.

RE: Todays Project - What did you do today? - EdK - 07-04-2013

Holy crap that's a lot of wood. I'll bet you're glad you got it done though.
It's hot in Minnesota today also. It got up to 89F. Not nearly as hot as it's been in the southwest but hot enough for this old fart to fire up the air conditioning.

Ed