+- MetalworkingFun Forum (http://www.metalworkingfun.com)
+-- Forum: Machining (http://www.metalworkingfun.com/forum-5.html)
+--- Forum: Welding & Casting (http://www.metalworkingfun.com/forum-9.html)
+---- Forum: Blacksmithing (http://www.metalworkingfun.com/forum-29.html)
+---- Thread: Coke Forge Build (/thread-2189.html)
RE: Coke Forge Build - doubleboost - 08-17-2014
Hi
Rob
Is that a single phase motor 240 volt
Seems a bit easy for you
No need to rewire it or play with capacitors
John
RE: Coke Forge Build - vtsteam - 08-17-2014
A bit of screen and its BEFC motor.
(I got the B from Doubleboost videos.)
RE: Coke Forge Build - RobWilson - 08-18-2014
I here you Mick , its the way my luck goes
Aye way to easy John
Rob
RE: Coke Forge Build - RobWilson - 08-23-2014
Finished up the blower doodle , should look something like this when done
![[Image: blower2_zps046c35d2.jpg]](http://s1066.photobucket.com/user/RobWilson100/media/Forge/blower2_zps046c35d2.jpg.html)
![[Image: blower1_zps930e23e8.jpg]](http://s1066.photobucket.com/user/RobWilson100/media/Forge/blower1_zps930e23e8.jpg.html)
Hopefully
Rob
RE: Coke Forge Build - doubleboost - 08-23-2014
Looks like the "scetchograph" is working fine
Good looking fan
John
RE: Coke Forge Build - krv3000 - 08-23-2014
well thats brill
RE: Coke Forge Build - hermetic - 08-24-2014
Wirenuts! American? we were using them in the 1930,s Ill have you know. They were called scruits, and came with the tag line "atwist of the wrist makes the joint"
https://www.flickr.com/photos/govert1970/6192436099/
Phil
East Yorks.
RE: Coke Forge Build - EdK - 08-24-2014
"William P. Marr emigrated from Scotland to Ontario, Canada early in the twentieth century. After settling in the Toronto area, he was employed as a contractor for Ontario Hydro, where he worked as an electrician, converting gas-lit homes to electrical incandescent lighting.
At that time, the accepted practice for joining conductors was a process called solder and tape. Typically, a mechanic would first install the insulated wires; then an electrician cleaned the exposed conductors, twisted them together, then firmly joined the conductors's ends by dipping them into a pot of molten solder. After cooling, the jointed exposed conductors were wrapped with insulating tape.
The process was time-consuming and potentially dangerous. Marr was injured when he spilled molten solder on himself. Seeking a safer and more efficient way of joining electrical conductors, Marr, working in his home workshop, developed the first pressure-type wire connector and, in 1914, produced a set-screw version which was the forerunner to the present-day twist-on connector now used in North America."
RE: Coke Forge Build - awemawson - 08-24-2014
Certainly I can remember screw on porcelain ones used in my parent house that was built just pre-war (1939-45 war) - probably 1937-8 along with rubber and cotton '7-029' wires
RE: Coke Forge Build - RobWilson - 08-24-2014
(08-24-2014, 08:36 AM)hermetic Wrote: Wirenuts! American? we were using them in the 1930,s Ill have you know. They were called scruits, and came with the tag line "atwist of the wrist makes the joint"
https://www.flickr.com/photos/govert1970/6192436099/
Phil
East Yorks.
"Ill have you no" they were invented across the pond , my memory failed me ,as Ed points out they were invented in Canada 1914 .
Rob