+- MetalworkingFun Forum (http://www.metalworkingfun.com)
+-- Forum: Machining (http://www.metalworkingfun.com/forum-5.html)
+--- Forum: Projects (http://www.metalworkingfun.com/forum-7.html)
+--- Thread: Bending Iron (/thread-4011.html)
Pages:
1
2
Bending Iron - TomG - 03-08-2019
I'm putting the finishing touches on a bending iron I've been working on, so I thought it would be a good time to share.
The iron itself is made from a chunk of aluminum roughly 3" x 5" x 7". A shaper would have been the machine of choice to rough out the airfoil shape, but since I don't have one, multiple passes with a fly cutter got the job done. The finishing was accomplished on the belt sander. There is one 1/4-20 tapped hole in the center for a thermocouple and a couple more for mounting purposes. The cartridge heaters were 12mm in diameter, so I had to wait on a reamer to put the holes in for them. I spaced the iron about 1/4" above the mounting plate on ptfe washers. I'm not sure of the exact operating temperature yet, but they should be good to around 500F. If not, I can always go to a different material. The PID controller and SSR are cheapies off Amazon, but work very well. The whole thing passed the smoke test today and ran up to 250ºF in about three minutes. I suspect it'll need to get up around 400ºF in use, and it doesn't look like that will be a problem. I still have to add a strain relief on the cord and maybe a power switch before buttoning up the enclosure.
Tom
![[Image: 20190228_131251.jpg]](https://photos.imageevent.com/tomgriffin/generalstuff/large/20190228_131251.jpg)
![[Image: 20190228_142653.jpg]](https://photos.imageevent.com/tomgriffin/generalstuff/large/20190228_142653.jpg)
![[Image: 20190228_152131.jpg]](https://photos.imageevent.com/tomgriffin/generalstuff/large/20190228_152131.jpg)
![[Image: 20190308_170118.jpg]](https://photos.imageevent.com/tomgriffin/generalstuff/large/20190308_170118.jpg)
![[Image: 20190308_170157.jpg]](https://photos.imageevent.com/tomgriffin/generalstuff/large/20190308_170157.jpg)
RE: Bending Iron - awemawson - 03-08-2019
er? Bending WHAT Tom ??????
RE: Bending Iron - Vinny - 03-08-2019
I was wondering the same thing.
RE: Bending Iron - Pete O - 03-08-2019
Methinks this has something to do with making a cello.
RE: Bending Iron - Clifford B. - 03-08-2019
I B curious too .....................
RE: Bending Iron - TomG - 03-08-2019
It's a tool used by luthiers to bend wood for making stringed instruments. Yes, this one will be used to bend the ribs of a cello.
Tom
RE: Bending Iron - awemawson - 03-09-2019
I'm sure Stradivarius never had anything like that !
RE: Bending Iron - TomG - 03-09-2019
The idea of making one out of iron and throwing it in the wood fire just didn't appeal to me.
RE: Bending Iron - Highpower - 03-09-2019
(03-09-2019, 08:08 AM)TomG Wrote: The idea of making one out of iron and throwing it in the wood fire just didn't appeal to me.
.... Sez the guy that made his own wood screws from scratch in the past.
RE: Bending Iron - Vinny - 03-09-2019
Since he retired he has absolutely no sense of adventure.