MetalworkingFun Forum › Machinery › Milling Machines v
Prep For Machining Cast Iron

Thread Modes
Prep For Machining Cast Iron
EdK Offline
Whipping Boy
*******
Posts: 8,854
Threads: 318
Joined: Feb 2012
Location: Arizona/Minnesota
The following 3 users Like EdK's post:
Vinny (12-28-2023), f350ca (12-28-2023), JScott (12-29-2023)
#1
12-28-2023, 03:00 PM
Condomized the mill for machining cast iron.

Ed

   
Reply
Thanks given by:
rleete Offline
Senior
*****
Posts: 768
Threads: 47
Joined: Mar 2012
Location: Rochester, NY
The following 3 users Like rleete's post:
Vinny (12-28-2023), EdK (12-28-2023), Highpower (12-28-2023)
#2
12-28-2023, 03:28 PM
Quite the optimist, aren't you?
Full of ideas, but slow to produce parts
Reply
Thanks given by:
EdK Offline
Whipping Boy
*******
Posts: 8,854
Threads: 318
Joined: Feb 2012
Location: Arizona/Minnesota
#3
12-28-2023, 03:39 PM
(12-28-2023, 03:28 PM)rleete Wrote: Quite the optimist, aren't you?

Probably. Rotfl

Ed
Reply
Thanks given by:
Hawkeye Offline
Junior
****
Posts: 535
Threads: 39
Joined: Jan 2013
Location: Kelowna, BC, Canada
The following 1 user Likes Hawkeye's post:
EdK (12-29-2023)
#4
12-28-2023, 10:50 PM
Hey, Ed. After you wash your hands, scrub them with shampoo. You'd be amazed how much more black you'll get out.
Mike

If you can't get one, make one.

Hawkeye, proud to be a member of MetalworkingFun Forum since Jan 2013.
Reply
Thanks given by: EdK
rleete Offline
Senior
*****
Posts: 768
Threads: 47
Joined: Mar 2012
Location: Rochester, NY
#5
12-29-2023, 12:08 PM
Do we get a hint as to what you are making?
Full of ideas, but slow to produce parts
Reply
Thanks given by:
EdK Offline
Whipping Boy
*******
Posts: 8,854
Threads: 318
Joined: Feb 2012
Location: Arizona/Minnesota
#6
12-30-2023, 12:19 AM
(12-29-2023, 12:08 PM)rleete Wrote: Do we get a hint as to what you are making?

A block to mount the QCTP on to eliminate the compound. I made one previously but for some really stupid reason I did not make it to the same height as the compound which requires me to adjust the tool holders in the QCTP when I switch between the block and the compound. A royal pain in the butt because of my stupidity!

I machined two sides of the block and found there ware ridges on the surfaces that pointed to an out of tram mill head so I de-condomized the mill and measured the tram. I was expecting the Y tram to be out based on the ridges but it was spot on and the X tram was within .00025" so out of tram was eliminated. Next I measured for jaw lift on the movable jaw of the vise but there was none at all. Perplexing to say the least.

So now I'm trying a fly cutter to see if I get better results. To be continued.  Bash

Ed
Reply
Thanks given by:
rleete Offline
Senior
*****
Posts: 768
Threads: 47
Joined: Mar 2012
Location: Rochester, NY
#7
12-30-2023, 03:19 PM
Maybe too much play in the ways? New mills have to run in a bit to seat, and then need to be readjusted to eliminate any play.
Full of ideas, but slow to produce parts
Reply
Thanks given by:
EdK Offline
Whipping Boy
*******
Posts: 8,854
Threads: 318
Joined: Feb 2012
Location: Arizona/Minnesota
#8
12-30-2023, 04:14 PM
(12-30-2023, 03:19 PM)rleete Wrote: Maybe too much play in the ways?  New mills have to run in a bit to seat, and then need to be readjusted to eliminate any play.

I don't think that's it. I've got the gibs fairly tight, but it's worth testing with a DI to see if there's any movement.

The fly cutter isn't working too well. I think the geometry of the cutting edge is not quite right so I'm going to put that project aside for now and work on something else until I get the tool ground properly.

Ed
Reply
Thanks given by:
rleete Offline
Senior
*****
Posts: 768
Threads: 47
Joined: Mar 2012
Location: Rochester, NY
#9
12-30-2023, 05:10 PM
Flycutting is the way to go. RPM slow, medium feed. Small radius on cutter, absolutely sharp. I don't use top rake for CI, but do for aluminum.
Full of ideas, but slow to produce parts
Reply
Thanks given by: EdK




Users browsing this thread: 6 Guest(s)