MetalworkingFun Forum › Machinery › Lathes v
Grizzly G0602 VFD conversion

Thread Modes
Grizzly G0602 VFD conversion
sun20ma Offline
Freshman
**
Posts: 18
Threads: 1
Joined: Jan 2018
Location: arizona
#11
01-21-2018, 12:39 PM
(01-21-2018, 12:13 PM)EdK Wrote:
(01-21-2018, 11:54 AM)sun20ma Wrote:
(01-21-2018, 11:52 AM)sun20ma Wrote: using remote controls and using existing panel controls

So you want to wire it like the document I attached but using your VFD, correct?

Ed

YES JUST LIKE   THX
Reply
Thanks given by:
Vinny Online
Another Whipping Boy
*******
Posts: 2,629
Threads: 101
Joined: Dec 2014
Location: Michigan
#12
01-21-2018, 12:58 PM
Welcome to the forum sun20ma!!!
Logan 200, Index 40H Mill, Boyer-Shultz 612 Surface Grinder, HF 4x6 Bandsaw, a shear with no name, ...
the nobucks boutique etsy shop  |  the nobucks boutique
Website
Reply
Thanks given by: sun20ma
Highpower Offline
JAFO
******
Posts: 4,493
Threads: 187
Joined: Feb 2012
Location: Missouri, USA
#13
01-21-2018, 01:41 PM
Welcome aboard sun20ma. Smiley-signs046
Willie
Reply
Thanks given by: sun20ma
Dr Stan Offline
Senior
*****
Posts: 2,328
Threads: 271
Joined: Jun 2014
Location: La Libertad, Philippines
#14
01-21-2018, 03:52 PM
Welcome to the asylum Thumbsup
Reply
Thanks given by: sun20ma
EdK Offline
Whipping Boy
*******
Posts: 8,888
Threads: 320
Joined: Feb 2012
Location: Arizona/Minnesota
#15
01-21-2018, 05:20 PM
Here you go sun20ma. If you have questions don't hesitate to ask. Do you have any experience with 120VAC wiring? If not, you should have someone that has experience help you with that part. The orange wires on the drawing are the AC voltage wiring.

Here's a link to a potentiometer for the speed control.

Potentiometer

Ed


.pdf   G0602 VFD.pdf (Size: 9.36 KB / Downloads: 14)
Reply
Thanks given by:
sun20ma Offline
Freshman
**
Posts: 18
Threads: 1
Joined: Jan 2018
Location: arizona
#16
01-21-2018, 07:17 PM
(01-21-2018, 05:20 PM)EdK Wrote: Here you go sun20ma. If you have questions don't hesitate to ask. Do you have any experience with 120VAC wiring? If not, you should have someone that has experience help you with that part. The orange wires on the drawing are the AC voltage wiring.

Here's a link to a potentiometer for the speed control.

Potentiometer

Ed

thanks again but most of the terminology does not correspond with the GS2-11PO VFD
Reply
Thanks given by:
Dr Stan Offline
Senior
*****
Posts: 2,328
Threads: 271
Joined: Jun 2014
Location: La Libertad, Philippines
#17
01-21-2018, 11:58 PM
For those needing a phase convertor I highly recommend Phase Craft. Sold on EBay by a builder in California. I'm very happy with my unit and have had it for about 5 years without any issues.
Reply
Thanks given by:
Highpower Offline
JAFO
******
Posts: 4,493
Threads: 187
Joined: Feb 2012
Location: Missouri, USA
#18
01-22-2018, 12:52 AM
You are using this VFD correct? https://cdn.automationdirect.com/static/...2m/ch2.pdf

Do you have the VFD wired to your power supply (breaker panel or electrical outlet) and the 3 phase motor yet?
IMO it's best to do that and make sure the motor operates properly with the VFD controls first, before tackling the remote wiring.

Is there a specific area with the wiring that is giving you problems?
Willie
Reply
Thanks given by:
Mayhem Offline
purveyor of mischief
******
Posts: 4,683
Threads: 93
Joined: Feb 2012
Location: Perth, Australia
#19
01-22-2018, 07:12 AM
Welcome aboard.
Hunting American dentists since 2015.
Reply
Thanks given by:
sun20ma Offline
Freshman
**
Posts: 18
Threads: 1
Joined: Jan 2018
Location: arizona
#20
01-22-2018, 10:02 AM
(01-22-2018, 12:52 AM)Highpower Wrote: You are using this VFD correct?  https://cdn.automationdirect.com/static/...2m/ch2.pdf

Do you have the VFD wired to your power supply (breaker panel or electrical outlet) and the 3 phase motor yet?
IMO it's best to do that and make sure the motor operates properly with the VFD controls first, before tackling the remote wiring.

Is there a specific area with the wiring that is giving you problems?

I have most of the electrical parts but I have not started the install   I just am not sure how to wire all the controls remotely   I want to use the existing switches and add a 53c35k pot, machtach  display with a GS2-11PO VFD and Leeson 192051 3ph
Reply
Thanks given by:




Users browsing this thread: 12 Guest(s)