MetalworkingFun Forum › Machinery › Lathes v
Gear lever not engaging

Thread Modes
Gear lever not engaging
aRM Offline
Sophmore
***
Posts: 214
Threads: 19
Joined: Oct 2014
Location: SOUTH AFRICA,KZN,DURBAN
#1
11-30-2016, 04:20 PM
Hi Guys
Am at my wits end with this bloody machine of mine ~!@#$%^&*()_P

Needed to cut Exterior Metric 1.5mm Threads. Machine panels says engage LCS6Y GEARS. Double-confirm from attached pic.
No problem with the alphabets but the Gear Lever for Numero 6 just won't Engage. That's the Lever in the Centre with the Blue/Red Numbers on either side in second picture.
Tried umpteenth times, even with lathe running in very low speed.  No dice  !!!  It just won't engage into 6. Try any other Number and she is ready to go.  
What am I  doing  wrong  ???
Why or what is causing the Lever to Jam ???
How would one soften the movement on this Lever  ???
Don't know much about these things, but is there no Clutch to soften the movements ???
Would immensely appreciate some help here as the Threads already cut just won't fit the internal one's cut manually with a Die already.
Thanks in advance (TIA)
Kind regards
aRM


       
Reply
Thanks given by:
f350ca Offline
Senior
*****
Posts: 3,003
Threads: 51
Joined: Apr 2012
Location: Ontario
#2
11-30-2016, 05:30 PM
Thats a lot of levers to set.
The plate mentions going through neutral before selecting a gear, could the numbered shifter still be in another gear? With the lathe running slow make sure the lead screw stops when that shifter is in neutral. Then try for 6th.
Free advice is worth exactly what you payed for it.
Greg
Reply
Thanks given by: aRM
Vinny Online
Another Whipping Boy
*******
Posts: 2,620
Threads: 100
Joined: Dec 2014
Location: Michigan
#3
11-30-2016, 06:19 PM
And the last one is in Z not Y, unless that's just where you stopped.
Logan 200, Index 40H Mill, Boyer-Shultz 612 Surface Grinder, HF 4x6 Bandsaw, a shear with no name, ...
the nobucks boutique etsy shop  |  the nobucks boutique
Website
Reply
Thanks given by: aRM
Dr Stan Offline
Senior
*****
Posts: 2,328
Threads: 271
Joined: Jun 2014
Location: La Libertad, Philippines
#4
11-30-2016, 08:48 PM
Do you have more than one lever out of gear?  If so that can be the problem on a lot of lathes.

Also rotate the spindle as you change gears as its a transmission just not synchronized .
Reply
Thanks given by:
Mayhem Offline
purveyor of mischief
******
Posts: 4,683
Threads: 93
Joined: Feb 2012
Location: Perth, Australia
#5
12-01-2016, 08:22 AM
(11-30-2016, 08:48 PM)Dr Stan Wrote: ...rotate the spindle as you change gears...

Rotate by hand, not under power.
Hunting American dentists since 2015.
Reply
Thanks given by: aRM
Dr Stan Offline
Senior
*****
Posts: 2,328
Threads: 271
Joined: Jun 2014
Location: La Libertad, Philippines
#6
12-01-2016, 10:38 AM
(12-01-2016, 08:22 AM)Mayhem Wrote:
(11-30-2016, 08:48 PM)Dr Stan Wrote: ...rotate the spindle as you change gears...

Rotate by hand, not under power.

Good catch.
Reply
Thanks given by:
f350ca Offline
Senior
*****
Posts: 3,003
Threads: 51
Joined: Apr 2012
Location: Ontario
#7
12-01-2016, 06:21 PM
It says to shift under 600 rpm, my Summit is the same, almost impossible to shift stopped and you don't roll it over by hand in the low gears.
Free advice is worth exactly what you payed for it.
Greg
Reply
Thanks given by:
Dr Stan Offline
Senior
*****
Posts: 2,328
Threads: 271
Joined: Jun 2014
Location: La Libertad, Philippines
The following 1 user Likes Dr Stan's post:
f350ca (12-01-2016)
#8
12-01-2016, 07:26 PM
(12-01-2016, 06:21 PM)f350ca Wrote: It says to shift under 600 rpm, my Summit is the same, almost impossible to shift stopped and you don't roll it over by hand in the low gears.

I still wonder if it has two or more levers out of gear.
Reply
Thanks given by:
Roadracer_Al Offline
Junior
****
Posts: 691
Threads: 14
Joined: Feb 2015
Location: Oakland, California
#9
12-01-2016, 10:04 PM
My lathe has a jog button in, what at first glance, appears to be the strangest place, on the right side, below all the shafts running the length of the bed.

However, when you're crouched down doing the gear changes, it suddenly makes perfect sense.
Reply
Thanks given by: aRM
aRM Offline
Sophmore
***
Posts: 214
Threads: 19
Joined: Oct 2014
Location: SOUTH AFRICA,KZN,DURBAN
#10
12-01-2016, 10:32 PM
(11-30-2016, 05:30 PM)f350ca Wrote: Thats a lot of levers to set.
The plate mentions going through neutral before selecting a gear, could the numbered shifter still be in another gear? With the lathe running slow make sure the lead screw stops when that shifter is in neutral. Then try for 6th.

Hi Greg
Indeed, did notice the Lead Screw does stop when in Neutral
Engaging into 6th is like there's no space there 17428
aRM
Reply
Thanks given by:




Users browsing this thread: 1 Guest(s)