MetalworkingFun Forum › Machining › Projects v
home made mill

Thread Modes
home made mill
krv3000 Offline
Senior
*****
Posts: 1,520
Threads: 157
Joined: Feb 2012
Location: uk
The following 3 users Like krv3000's post:
f350ca (08-01-2016), EdK (08-01-2016), Mayhem (08-01-2016)
#21
08-01-2016, 01:13 PM
hi all thanks for the comments all but dun gnaw as im on holiday I have had sum time to put the z and y bit on the base I had to make sum washers for the 4 fixing bolts there 5 mm thick od 32 mm with a 10.2 hole then just put it all back together and clocked the table in so its running parallel with the column run out at both ends the same with a dip in the middle I need to make two bushes for ether end as their is to much play in the end brackets and to drill them to put oilers in the next big job is I need to make a spacer block  to bring the head of the mill to the centre of the table  right pics  first pic of the dti is in the centre then next left then right


Attached Files Thumbnail(s)
                               
krv3000, proud to be a member of MetalworkingFun Forum since Feb 2012.
Reply
Thanks given by:
EdK Offline
Whipping Boy
*******
Posts: 8,854
Threads: 318
Joined: Feb 2012
Location: Arizona/Minnesota
#22
08-01-2016, 04:21 PM
Graemlin Thumbsup
Reply
Thanks given by:
oldskoolron Offline
Sophmore
***
Posts: 106
Threads: 23
Joined: Aug 2016
Location: in the bush qld australia
#23
08-19-2016, 05:26 AM
great setup at work man an the mill looks the guts Smiley-signs107
wish I could get some the large thick flat plate you got for your mill if I want stuff like that in oz I have to buy minimum of 3 meters
Reply
Thanks given by:
krv3000 Offline
Senior
*****
Posts: 1,520
Threads: 157
Joined: Feb 2012
Location: uk
The following 2 users Like krv3000's post:
f350ca (10-01-2016), EdK (10-01-2016)
#24
10-01-2016, 02:16 PM
big flat plate ant a problem nice bits of brass or aluminium is lol as we say over hear fees or famine any way did this to day the start of the extension for the mill head   hi all as promised the bare stock was spot on  100mm so I had to put sum weld on it to make it bigger  but before I did that I marked out the centre for the running centre to go in to then I lade dawn sum weld the finish size is 100 mm but the bar was not even so did this  to give me a nice finish I then set it up in the lathe and just turned it dawn to 100 mm there is sum holes where I have not put a nuff weld on these will just be field in as its not critical as it will be panted   then set up the fixt steady to bore out the end it needed to be 15mm deep by 70mm wide all dun the next step is to get it to john's to drill and put the two cut outs in for it to fit on to the Colom head right pics


Attached Files Thumbnail(s)
                               
krv3000, proud to be a member of MetalworkingFun Forum since Feb 2012.
Reply
Thanks given by:
Mayhem Offline
purveyor of mischief
******
Posts: 4,683
Threads: 93
Joined: Feb 2012
Location: Perth, Australia
The following 2 users Like Mayhem's post:
Vinny (10-01-2016), DaveH (10-14-2016)
#25
10-01-2016, 09:24 PM
Amazing that what looked like a log had steel inside it Big Grin

Nice work Bob
Hunting American dentists since 2015.
Reply
Thanks given by:
EdK Offline
Whipping Boy
*******
Posts: 8,854
Threads: 318
Joined: Feb 2012
Location: Arizona/Minnesota
The following 1 user Likes EdK's post:
DaveH (10-14-2016)
#26
10-02-2016, 09:27 AM
I thought it looked like a piece of a petrified tree trunk.

Ed
Reply
Thanks given by:
Roadracer_Al Offline
Junior
****
Posts: 691
Threads: 14
Joined: Feb 2015
Location: Oakland, California
The following 1 user Likes Roadracer_Al's post:
f350ca (10-02-2016)
#27
10-02-2016, 11:33 AM
So THATS what the metal stretcher looks like...
Reply
Thanks given by:
krv3000 Offline
Senior
*****
Posts: 1,520
Threads: 157
Joined: Feb 2012
Location: uk
The following 1 user Likes krv3000's post:
EdK (10-13-2016)
#28
10-13-2016, 04:11 PM
hi all thanks for the comments I dropped the mill head extension off at johns last night so he can cut the cut outs in the column for the fixing nuts so he will probably do a vid on the work that he is going  to do on it
krv3000, proud to be a member of MetalworkingFun Forum since Feb 2012.
Reply
Thanks given by:
Micktoon Offline
Junior
****
Posts: 638
Threads: 43
Joined: Sep 2012
Location: England
#29
10-13-2016, 04:27 PM
Hi Bob, nice job of expanding the bar  Graemlin  looking forward to seeing built up on the mill once John has done his work to it  Big Grin
Cheers mick
Micktoon, proud to be a member of MetalworkingFun since Sep 2012.
Reply
Thanks given by:
krv3000 Offline
Senior
*****
Posts: 1,520
Threads: 157
Joined: Feb 2012
Location: uk
#30
10-14-2016, 05:42 PM
hi that's just step one mick once he has dun that bit I then have to set it up on the mill column to see haw long it need to be then cut it off and then turn that end in to a male fitting to fit the mill head to then sort out the wiring and get a capacitor for the motor then make a stand Thumbsup
krv3000, proud to be a member of MetalworkingFun Forum since Feb 2012.
Reply
Thanks given by:




Users browsing this thread: 9 Guest(s)