MetalworkingFun Forum › Machinery › Milling Machines v
Setting Up My PM935 Mill

Thread Modes
Setting Up My PM935 Mill
EdK Offline
Whipping Boy
*******
Posts: 8,889
Threads: 320
Joined: Feb 2012
Location: Arizona/Minnesota
#581
08-06-2016, 05:14 PM
Got a little bit done today. Mounted the wired-up enclosure to the wall. I need to wire in the 220V line. It's the orange one to the left. Right now it's just powering the lathe through a disconnect switch so I could get the lathe back up and running after the shop space rearrangement. I need to find a 30A disconnect switch that will switch power to both the lathe and mill. The mill requires 30A, the lathe 20A.

Ed

   
Reply
Thanks given by:
Dr Stan Offline
Senior
*****
Posts: 2,328
Threads: 271
Joined: Jun 2014
Location: La Libertad, Philippines
#582
08-06-2016, 11:09 PM
(08-06-2016, 05:14 PM)EdK Wrote: I need to find a 30A disconnect switch that will switch power to both the lathe and mill. The mill requires 30A, the lathe 20A.

Ed

Just build a couple of knife switches.    Jawdrop   I'm sure you could slip the building inspector a Ben Franklin or two. Chin
Reply
Thanks given by:
EdK Offline
Whipping Boy
*******
Posts: 8,889
Threads: 320
Joined: Feb 2012
Location: Arizona/Minnesota
#583
08-07-2016, 12:36 AM
(08-06-2016, 11:09 PM)Dr Stan Wrote: the building inspector

What the hell is that? 17428 Big Grin

Ed
Reply
Thanks given by:
Highpower Offline
JAFO
******
Posts: 4,493
Threads: 187
Joined: Feb 2012
Location: Missouri, USA
#584
08-07-2016, 02:02 PM
(08-07-2016, 12:36 AM)EdK Wrote:
(08-06-2016, 11:09 PM)Dr Stan Wrote: the building inspector

What the hell is that?  17428    Big Grin

Ed

That would be the poor guy having the stroke if he were ever allowed to enter my basement! Rotfl

I've had to allow certain techs access into my shop for meter inspections /change outs (water / gas), phone line repairs, HVAC install, etc., and the first two words out of every mouth has been "HOLY (censored)!!!!!!" Big Grin
Willie
Reply
Thanks given by:
Dr Stan Offline
Senior
*****
Posts: 2,328
Threads: 271
Joined: Jun 2014
Location: La Libertad, Philippines
#585
08-07-2016, 02:26 PM
When I built my shop it had a 200 amp panel and one light and one outlet.  Just enough for the electrical inspector.   Smiley-eatdrink004
Reply
Thanks given by:
EdK Offline
Whipping Boy
*******
Posts: 8,889
Threads: 320
Joined: Feb 2012
Location: Arizona/Minnesota
The following 3 users Like EdK's post:
f350ca (08-13-2016), Highpower (08-14-2016), DaveH (08-14-2016)
#586
08-13-2016, 09:27 PM
Disconnect switch box moved and temporary wiring started. Lathe no longer has power.  Sadno

Ed

   
Reply
Thanks given by:
Highpower Offline
JAFO
******
Posts: 4,493
Threads: 187
Joined: Feb 2012
Location: Missouri, USA
The following 1 user Likes Highpower's post:
EdK (08-14-2016)
#587
08-14-2016, 12:15 PM
I'd rather do electrical wiring all day long than have to move another mill downstairs. Smile
Willie
Reply
Thanks given by:
EdK Offline
Whipping Boy
*******
Posts: 8,889
Threads: 320
Joined: Feb 2012
Location: Arizona/Minnesota
#588
08-14-2016, 12:33 PM
(08-14-2016, 12:15 PM)Highpower Wrote: I'd rather do electrical wiring all day long than have to move another mill downstairs.   Smile

Ya got that right Willie. Thumbsup

Ed
Reply
Thanks given by:
EdK Offline
Whipping Boy
*******
Posts: 8,889
Threads: 320
Joined: Feb 2012
Location: Arizona/Minnesota
The following 5 users Like EdK's post:
f350ca (09-05-2016), Highpower (09-06-2016), arvidj (09-06-2016), PixMan (09-07-2016), DaveH (09-07-2016)
#589
09-05-2016, 09:00 PM
Just so you guys don't think I'm sloughing off, I got the 220VAC wiring done.

Ed

   
Reply
Thanks given by:
Mayhem Offline
purveyor of mischief
******
Posts: 4,683
Threads: 93
Joined: Feb 2012
Location: Perth, Australia
The following 6 users Like Mayhem's post:
f350ca (09-06-2016), EdK (09-06-2016), DaveH (09-06-2016), Vinny (09-06-2016), PixMan (09-07-2016), arvidj (09-07-2016)
#590
09-06-2016, 06:09 AM
Gee Ed, at this rate we will be able to move this thread into the vintage machine section...
Hunting American dentists since 2015.
Reply
Thanks given by:




Users browsing this thread: 11 Guest(s)