MetalworkingFun Forum › Machinery › Milling Machines v
[PROJECT] X Power Feed

Thread Modes
Project X Power Feed
EdK Offline
Whipping Boy
*******
Posts: 8,888
Threads: 320
Joined: Feb 2012
Location: Arizona/Minnesota
#41
02-08-2015, 08:49 PM
Ken,

I plan on doing some rounding of the edges. Now that I know it all fits together properly I can work on making it prettier.

Ed
Reply
Thanks given by:
Mayhem Offline
purveyor of mischief
******
Posts: 4,683
Threads: 93
Joined: Feb 2012
Location: Perth, Australia
#42
02-09-2015, 05:10 AM
Ed - not a criticism but a question: is there any reason you didn't make it out of a single piece? I'm guessing it was what you had in "inventory" but curious if there is another reason.

Either way it is a beautiful bit of work.
Hunting American dentists since 2015.
Reply
Thanks given by: EdK
stevec Offline
69 yr. old senior
*****
Posts: 2,685
Threads: 29
Joined: Feb 2012
Location: Nova Scotia, Canada
#43
02-09-2015, 07:15 AM
Looking good Ed, glad to read that you plan to round those edges.
Busy Bee 12-36 lathe, Busy Bee Mill drill, Busy Bee 4x6 bandsaw, Homemade 9x17 bandsaw, Ad infinitum.
Reply
Thanks given by: EdK
EdK Offline
Whipping Boy
*******
Posts: 8,888
Threads: 320
Joined: Feb 2012
Location: Arizona/Minnesota
#44
02-09-2015, 08:31 AM
(02-09-2015, 05:10 AM)Mayhem Wrote: Ed - not a criticism but a question: is there any reason you didn't make it out of a single piece?  I'm guessing it was what you had in "inventory" but curious if there is another reason.

Either way it is a beautiful bit of work.

As you surmised, inventory dictated what I used.  Smile
Well, also I'm following Henry's method and he used a two piece design.

Ed
Reply
Thanks given by:
EdK Offline
Whipping Boy
*******
Posts: 8,888
Threads: 320
Joined: Feb 2012
Location: Arizona/Minnesota
#45
02-09-2015, 08:33 AM
(02-09-2015, 07:15 AM)stevec Wrote: Looking good Ed, glad to  read that you plan to round those edges.

Ya, those corner are sharp. I think I may taper the sides inward a bit also.

Ed
Reply
Thanks given by:
stevec Offline
69 yr. old senior
*****
Posts: 2,685
Threads: 29
Joined: Feb 2012
Location: Nova Scotia, Canada
#46
02-09-2015, 10:33 AM
Ed, it would be good if you had a power feed to do those corners and tapers. Rotfl

Steve

Smiley-eatdrink004
Busy Bee 12-36 lathe, Busy Bee Mill drill, Busy Bee 4x6 bandsaw, Homemade 9x17 bandsaw, Ad infinitum.
Reply
Thanks given by:
EdK Offline
Whipping Boy
*******
Posts: 8,888
Threads: 320
Joined: Feb 2012
Location: Arizona/Minnesota
The following 2 users Like EdK's post:
arvidj (02-09-2015), DaveH (02-09-2015)
#47
02-09-2015, 01:10 PM
(02-09-2015, 10:33 AM)stevec Wrote: Ed, it would be good if you had a power feed to do those corners and tapers. Rotfl

Steve

Smiley-eatdrink004

Rotfl

Kind of like needing a welding table to make a welding table.

Ed
Reply
Thanks given by:




Users browsing this thread: 9 Guest(s)