MetalworkingFun Forum › Machining › General Metalworking Discussion v
help with angle iron's

Thread Modes
help with angle iron's
EdK Offline
Whipping Boy
*******
Posts: 8,854
Threads: 318
Joined: Feb 2012
Location: Arizona/Minnesota
#41
01-15-2015, 06:36 PM
(01-15-2015, 06:33 PM)stevec Wrote: That's a pretty slow suck-up Dave Sweat

What do you mean Steve? Two hours isn't too bad. Big Grin

Ed
Reply
Thanks given by:
DaveH Offline
Child of the 60's
******
Posts: 4,513
Threads: 139
Joined: Feb 2012
Location: Kempton Park. South Africa
The following 1 user Likes DaveH's post:
EdK (01-15-2015)
#42
01-15-2015, 06:58 PM
(01-15-2015, 06:36 PM)EdK Wrote:
(01-15-2015, 06:33 PM)stevec Wrote: That's a pretty slow suck-up Dave Sweat

What do you mean Steve? Two hours isn't too bad.  Big Grin

Ed

My internet went down 6799

(didn't really Big Grin Big Grin Big Grin )
Reply
Thanks given by:
dbreeze225 Offline
Freshman
**
Posts: 19
Threads: 2
Joined: Jan 2015
Location: New York
#43
01-16-2015, 06:40 PM
hey guys i didnt do any polishing today i was to busy
i did start sanding a new piece tho
doing this type of sanding i have been doing it by hand
so much effort today i just didnt have the energy can i use a power sander on this type of aluminum
i have a few different types i got the belt sander, and attached to it also has a rotating dis sander.....
also i got a handheld one that doesnt spin you put a square piece on and it vibrates (i dont know the name of this type of sander)
i have been told doing it by hand is alot better i was thinking of maybe doing the lower grits with the power hand held one
then the last 2 (finer grits) by hand ........any suggestions?
i know i am looking for a short cut just wiped out today and it was a thought but i dont know if i should go that route or not i have never sanded this type of metal with power????
Reply
Thanks given by:
EdK Offline
Whipping Boy
*******
Posts: 8,854
Threads: 318
Joined: Feb 2012
Location: Arizona/Minnesota
#44
01-16-2015, 06:55 PM
Dave,

Try it on a small sample and see how it turns out. I have one of these that might work well.

http://www.homedepot.com/p/Ryobi-Detail-...5yc1vZc29d

Ed
Reply
Thanks given by:
DaveH Offline
Child of the 60's
******
Posts: 4,513
Threads: 139
Joined: Feb 2012
Location: Kempton Park. South Africa
#45
01-16-2015, 06:56 PM
Hi Dave - nothing wrong with trying to find an easier way, sometimes it can turn out to be a better way. Smile 

Me - I would try anything I had.
First try it out on a bit of scrap and now you are looking at power tools THINK SAFETY you don't want it flying across the room.
You also need to think about SELF SAFETY. - hands and face especially.
Go for it. See which one suits best.
Smiley-eatdrink004 
DaveH
Reply
Thanks given by:
dbreeze225 Offline
Freshman
**
Posts: 19
Threads: 2
Joined: Jan 2015
Location: New York
#46
01-16-2015, 07:12 PM
http://www.homedepot.com/p/Ryobi-2-Amp-1...5yc1vZc28s

i have something similar to this not exactly but very close.
what i was most worried out is maybe the sander heating up the aluminum to much in the process.
but if i use scap you right cant ruin scap so we will see tomorow to tired tonight
Reply
Thanks given by:
dbreeze225 Offline
Freshman
**
Posts: 19
Threads: 2
Joined: Jan 2015
Location: New York
#47
01-16-2015, 07:20 PM
hey if i try the power hand held sander you guys think i should still put a bunch of water down on the piece and some on the paper or not ???
Reply
Thanks given by:
DaveH Offline
Child of the 60's
******
Posts: 4,513
Threads: 139
Joined: Feb 2012
Location: Kempton Park. South Africa
The following 1 user Likes DaveH's post:
EdK (01-16-2015)
#48
01-16-2015, 07:23 PM
It will heat up quite quickly - keep a gentle light touch.
Allow it to cool down every now and then.

Unless the sander is completely 100% water proof you cannot use any water - unless you have a death wish  Big Grin
Smiley-eatdrink004 
DaveH

 
Reply
Thanks given by:
EdK Offline
Whipping Boy
*******
Posts: 8,854
Threads: 318
Joined: Feb 2012
Location: Arizona/Minnesota
The following 1 user Likes EdK's post:
DaveH (01-16-2015)
#49
01-16-2015, 07:29 PM
Water and power tools don't mix at all. Definitely do not use water. A light touch and keep the sander moving and clear the aluminum dust frequently.

Ed
Reply
Thanks given by:
f350ca Offline
Senior
*****
Posts: 3,003
Threads: 51
Joined: Apr 2012
Location: Ontario
The following 1 user Likes f350ca's post:
EdK (01-16-2015)
#50
01-16-2015, 08:59 PM
Go back to post #6
Free advice is worth exactly what you payed for it.
Greg
Reply
Thanks given by:




Users browsing this thread: 11 Guest(s)