MetalworkingFun Forum › Machining › General Metalworking Discussion v
Dumpster Dive Results

Thread Modes
Dumpster Dive Results
arvidj Offline
Junior
****
Posts: 742
Threads: 35
Joined: Feb 2012
Location: Minneapolis, MN
The following 1 user Likes arvidj's post:
EdK (12-12-2014)
#31
12-12-2014, 03:56 PM
Smiley-signs107

I'm going to have to get a job where they throw away something more substantial than old code. I can have all the buckets of old bits I can carry [that would be computer 'bits' ... 1 and 0's] but it's difficult to make anything meaningful with them.
Reply
Thanks given by:
EdK Offline
Whipping Boy
*******
Posts: 8,898
Threads: 320
Joined: Feb 2012
Location: Arizona/Minnesota
#32
12-12-2014, 04:05 PM
Tough to weld those bits for sure.

The company is moving to Shakopee in a about a month and they want to move as little as possible so bins upon bins, large bins on wheels, are being thrown out. I'd rather forgo the dumpster dives and have the company stay where they are but that's not going to happen so I may as well benefit somehow.

Ed
Reply
Thanks given by:
arvidj Offline
Junior
****
Posts: 742
Threads: 35
Joined: Feb 2012
Location: Minneapolis, MN
#33
12-12-2014, 08:30 PM
(12-12-2014, 04:05 PM)EdK Wrote: ... The company is moving to Shakopee in a about a month ...

Ed

Wow, you get to drive to within a few miles of my house every day. I am sure you are looking forward to that.

Where exactly in Shakopee?

Arvid
Reply
Thanks given by:
Mayhem Offline
purveyor of mischief
******
Posts: 4,683
Threads: 93
Joined: Feb 2012
Location: Perth, Australia
#34
12-12-2014, 08:31 PM
What size are they Ed?
Hunting American dentists since 2015.
Reply
Thanks given by:
EdK Offline
Whipping Boy
*******
Posts: 8,898
Threads: 320
Joined: Feb 2012
Location: Arizona/Minnesota
#35
12-12-2014, 08:59 PM
(12-12-2014, 08:30 PM)arvidj Wrote:
(12-12-2014, 04:05 PM)EdK Wrote: ... The company is moving to Shakopee in a about a month ...

Ed

Wow, you get to drive to within a few miles of my house every day. I am sure you are looking forward to that.

Where exactly in Shakopee?

Arvid

Just east of Canterbury Downs race track. Just north of 169. I'm guessing it'll add 10 minutes to my morning commute and 15 to my evening commute. I am not looking forward to it but I just need to tough it out for about 4 more years and I'll be home free. At least that's my plan.

Ed
Reply
Thanks given by:
EdK Offline
Whipping Boy
*******
Posts: 8,898
Threads: 320
Joined: Feb 2012
Location: Arizona/Minnesota
#36
12-12-2014, 09:01 PM
(12-12-2014, 08:31 PM)Mayhem Wrote: What size are they Ed?

I'd guess they are about 5 feet by three feet by three feet tall. That's about as big as will fit in the elevator. Engineering is on the second floor so we are limited to what we can bring up and down in the elevator.

Ed
Reply
Thanks given by:
Mayhem Offline
purveyor of mischief
******
Posts: 4,683
Threads: 93
Joined: Feb 2012
Location: Perth, Australia
#37
12-12-2014, 10:19 PM
I meant the bearings Ed Big Grin
Hunting American dentists since 2015.
Reply
Thanks given by:
EdK Offline
Whipping Boy
*******
Posts: 8,898
Threads: 320
Joined: Feb 2012
Location: Arizona/Minnesota
#38
12-12-2014, 10:23 PM
(12-12-2014, 10:19 PM)Mayhem Wrote: I meant the bearings Ed Big Grin

Doh! Slaphead

NTA-1423

ID: 22mm x OD: 36mm x W: 2mm

NTA-1625
ID: 1 x OD: 1.562 x W: 0.116 Inches

Ed Blush
Reply
Thanks given by:
stevec Offline
69 yr. old senior
*****
Posts: 2,685
Threads: 29
Joined: Feb 2012
Location: Nova Scotia, Canada
#39
12-13-2014, 07:09 AM
Ed, that sounds really thin, are they just the rollers and cages without the races?
Busy Bee 12-36 lathe, Busy Bee Mill drill, Busy Bee 4x6 bandsaw, Homemade 9x17 bandsaw, Ad infinitum.
Reply
Thanks given by:
EdK Offline
Whipping Boy
*******
Posts: 8,898
Threads: 320
Joined: Feb 2012
Location: Arizona/Minnesota
#40
12-13-2014, 10:26 AM
The flat washers in the bag next to the upper bearing are used with that bearing. I didn't get any of the washers for the lower bearing but they are cheap and available from McMaster if I were to need them.

Ed

   
Reply
Thanks given by: stevec




Users browsing this thread: 8 Guest(s)