11-06-2014, 12:51 PM
The only case where runout would matter is if you are setting the diameter by miking over the bar and tool. If the bar has runout it would give you a false reading.
Tom
Tom
![[Image: TomsTechLogo-Profile.png]](http://tomstechniques.com/wp-content/uploads/2013/11/TomsTechLogo-Profile.png)
|
Between centers boring bar
|
 
11-06-2014, 01:07 PM
My boring bar has a slight bend in it
Makes no difference at all John 
11-06-2014, 01:10 PM
(11-06-2014, 12:51 PM)TomG Wrote: The only case where runout would matter is if you are setting the diameter by miking over the bar and tool. If the bar has runout it would give you a false reading. Well, if the bar has runout, how do you set the bore diameter? Trial and error? I'm going to try to make another between centers bar, this time from 1/2" drill rod. Chuck
Micromark 7x14 Lathe, X2 Mill , old Green 4x6 bandsaw
The difficult takes me a while, the impossible takes a little longer.
11-06-2014, 01:21 PM
Sorry Tom
But it will not be a problem ,take cut measure the bore , Mike the cutter from the the back of the bar and adjust as required The cutter in a bent bar is considered a fixed point , therefor the required adjustment is easily done Stuart
Lordedmond, proud to be a member of MetalworkingFun Forum since Jul 2013.
11-06-2014, 02:44 PM
(11-06-2014, 01:10 PM)chucketn Wrote:(11-06-2014, 12:51 PM)TomG Wrote: The only case where runout would matter is if you are setting the diameter by miking over the bar and tool. If the bar has runout it would give you a false reading. Not trial and error, just trial. Assuming the part you are boring is mounted on the cross slide of the lathe, take a trial cut, zero the cross feed dial and measure the bore. Then move the part away from the tool the required amount and using the wall of the bore as a stop, move the tool bit out until it re-touches. Now when the dial gets back to zero, the bore will be to size. Better take a couple trial cuts to check your work before taking it to size. This is basically the same technique I use to set a boring head to machine a radius. Pick up the edge of the part and move it over the required amount, then run the boring head out until the tool contacts the edge. Tom 
11-06-2014, 10:19 PM
A half inch boring bar is quite small and can lead to chatter & flex. Is that the largest bar that will fit in the hole?
11-07-2014, 06:49 AM
(11-06-2014, 10:19 PM)Dr Stan Wrote: A half inch boring bar is quite small and can lead to chatter & flex. Is that the largest bar that will fit in the hole? Yes, the largest long drill I have is 1/2" MT1. I'm looking for a few bigger ones that are affordable. Chuck
Micromark 7x14 Lathe, X2 Mill , old Green 4x6 bandsaw
The difficult takes me a while, the impossible takes a little longer.  (11-06-2014, 11:54 AM)chucketn Wrote: Whew! It finally makes séance! Thanks for all the input.Good one chuck!
Busy Bee 12-36 lathe, Busy Bee Mill drill, Busy Bee 4x6 bandsaw, Homemade 9x17 bandsaw, Ad infinitum.
11-07-2014, 12:42 PM
What is the length/depth of the hole?
What is the finished diameter? What precision is needed? What is the material? Do you have a boring head that can be mounted in the head stock? What sort of selection of single ended end mills do you have?
11-07-2014, 12:45 PM
When I made mine I bored the casting first
Then made the spindle It is easier that way John |
|
« Next Oldest | Next Newest »
|
Users browsing this thread: 3 Guest(s)