|
Tool Grinder
|
06-12-2013, 05:46 PM
well i did give it a wash the best thing i have fawned for rust removing is free its acid from car batterers no need for electrolysis just put the part in and leev for 5 to 10 mini-ts see the pics be for and after of a drill chuck i got at the boot sale
krv3000, proud to be a member of MetalworkingFun Forum since Feb 2012.
06-12-2013, 05:50 PM
(06-12-2013, 05:46 PM)krv3000 Wrote: well i did give it a wash the best thing i have fawned for rust removing is free its acid from car batterers no need for electrolysis just put the part in and leev for 5 to 10 mini-ts see the pics be for and after of a drill chuck i got at the boot sale Bob, Wow! That acid did a nice job on the chuck.  Ed 
06-13-2013, 02:27 AM
Now thats what you call a good result Bob
I was just about to chuck out two old car batteries I will drain them first after seeing that Bob  Cheers Mick
Micktoon, proud to be a member of MetalworkingFun since Sep 2012.
06-13-2013, 06:08 AM
Wow - that did come up nice Bob.
Knowing my luck I would get side tracked and forget and then come back to an empty bucket! At least with the electrolysis there is no harm done if you forget about it. I haven't reversed the process Steve - is it something you recommend?
Hunting American dentists since 2015.
06-13-2013, 10:03 AM
(06-13-2013, 06:08 AM)Mayhem Wrote: I haven't reversed the process Steve - is it something you recommend?Nope, I was hoping you had experimented so I wouldn't have to. When and if I get around to it I'll report my findings.
Busy Bee 12-36 lathe, Busy Bee Mill drill, Busy Bee 4x6 bandsaw, Homemade 9x17 bandsaw, Ad infinitum.
06-13-2013, 04:55 PM
av you had it runing yet john
krv3000, proud to be a member of MetalworkingFun Forum since Feb 2012.
06-14-2013, 06:36 AM
(06-13-2013, 10:03 AM)stevec Wrote:(06-13-2013, 06:08 AM)Mayhem Wrote: I haven't reversed the process Steve - is it something you recommend?Nope, I was hoping you had experimented so I wouldn't have to. I haven't had to clean the anode much since changing to graphite (although the electrolyte gets very black, very quickly) - works just as well, as far as I can tell, either for electrolytic rust removal or in an anodizing setup. I use arc brazing rods and strip all but an inch of the copper coating with ferric chloride (for etching PCBs), leaving somewhere to solder connections, much more reliable than clamps and clips.
Rules are for the obedience of fools, and the guidance of wise men...
(Douglas Bader) 
06-15-2013, 12:10 PM
Hi
Lads Cleaned the grinder up a bit The motor is not very quiet I stripped it and cleaned the bearings re packed with grease A lot better (the bearings are specials) I turned up a couple of bosses and mounted a green wheel A bit play with a 60 deg threading tool very happy with the results ![[Image: IMG_4669_zps1c6eae48.jpg]](http://s261.photobucket.com/user/john970s0/media/IMG_4669_zps1c6eae48.jpg.html) ![[Image: IMG_4665_zps12b9f5d9.jpg]](http://s261.photobucket.com/user/john970s0/media/IMG_4665_zps12b9f5d9.jpg.html) ![[Image: IMG_4663_zps48017e83.jpg]](http://s261.photobucket.com/user/john970s0/media/IMG_4663_zps48017e83.jpg.html) ![[Image: IMG_4656_zps979e2b66.jpg]](http://s261.photobucket.com/user/john970s0/media/IMG_4656_zps979e2b66.jpg.html) ![[Image: IMG_4652_zps6b8b79ac.jpg]](http://s261.photobucket.com/user/john970s0/media/IMG_4652_zps6b8b79ac.jpg.html) ![[Image: IMG_4655_zps83f838e3.jpg]](http://s261.photobucket.com/user/john970s0/media/IMG_4655_zps83f838e3.jpg.html) John |
|
« Next Oldest | Next Newest »
|
