MetalworkingFun Forum › Machinery › Milling Machines v
Fixing a Leaky RF-45 Mill Head - Enco

Thread Modes
Fixing a Leaky RF-45 Mill Head - Enco
EdK Offline
Whipping Boy
*******
Posts: 8,889
Threads: 320
Joined: Feb 2012
Location: Arizona/Minnesota
#101
04-05-2012, 06:04 PM
(04-05-2012, 05:54 PM)DaveH Wrote: Ed, I don't think that is expensive, bearings (good ones that is) have never been cheap. Nor have the seals.

Smiley-eatdrink004
DaveH

Dave,

That's the way I look at it to. Smile

Ed
Reply
Thanks given by:
Highpower Offline
JAFO
******
Posts: 4,493
Threads: 187
Joined: Feb 2012
Location: Missouri, USA
#102
04-05-2012, 09:10 PM
And it's cheaper than buying a new mill. Happyyes
Willie
Reply
Thanks given by:
EdK Offline
Whipping Boy
*******
Posts: 8,889
Threads: 320
Joined: Feb 2012
Location: Arizona/Minnesota
#103
04-06-2012, 06:37 AM
(04-05-2012, 09:10 PM)Highpower Wrote: And it's cheaper than buying a new mill. Happyyes

Except, I likely am buying a new mill. Just like the one Arvid ordered. But, I couldn't sell my current mill with a leaky head with a clear conscience so I have to get this mill all spruced up and functioning to a level that I would find acceptable if I were going to keep it.

Ed
Reply
Thanks given by:
Highpower Offline
JAFO
******
Posts: 4,493
Threads: 187
Joined: Feb 2012
Location: Missouri, USA
#104
04-06-2012, 07:33 AM
Ahhh.... I see how it is now. You've been holding out on us! Tongue

That's cool. Getting a new machine or tool is always a sure way to brighten your day. Of course there is nothing wrong with having an extra one on hand for second operations. Just saying..... Big Grin
Willie
Reply
Thanks given by:
EdK Offline
Whipping Boy
*******
Posts: 8,889
Threads: 320
Joined: Feb 2012
Location: Arizona/Minnesota
#105
04-09-2012, 05:49 PM
(04-06-2012, 07:33 AM)Highpower Wrote: Ahhh.... I see how it is now. You've been holding out on us! Tongue

That's cool. Getting a new machine or tool is always a sure way to brighten your day.

Willie,

Actually I've not been holding out. See this thread.

http://www.metalworkingfun.com/showthread.php?tid=65

Ed
Reply
Thanks given by:
Highpower Offline
JAFO
******
Posts: 4,493
Threads: 187
Joined: Feb 2012
Location: Missouri, USA
#106
04-09-2012, 07:38 PM
I remember the thread, but I don't remember you actually ordering it yet.

But then again, since I have "oldtimers" disease - there isn't a whole lot I do remember these days. Smiley-think005

Big Grin
Willie
Reply
Thanks given by:
EdK Offline
Whipping Boy
*******
Posts: 8,889
Threads: 320
Joined: Feb 2012
Location: Arizona/Minnesota
#107
04-27-2012, 08:13 PM
OK, it's time to get back to this project. I have most of the weekend allocated for working on the mill head rebuild. I have all of the parts and I finished my diversion project which was to drill and tap two holes in the mill head carrier so I can mount a bracket that will hold the gas springs on when I get around to that project.

Ed
Reply
Thanks given by:
henryarnold Offline
Sophmore
***
Posts: 170
Threads: 9
Joined: Apr 2012
Location: Southern California
#108
04-28-2012, 11:19 AM
(04-27-2012, 08:13 PM)EdAK Wrote: OK, it's time to get back to this project. I have most of the weekend allocated for working on the mill head rebuild. I have all of the parts and I finished my diversion project which was to drill and tap two holes in the mill head carrier so I can mount a bracket that will hold the gas springs on when I get around to that project.

Ed

Ed,
I'm on vacation this week so I'll be starting the work on my leaky mill. I'm looking forward to your posts showing how you finished the work.
Henry Arnold
henryarnold, proud to be a member of MetalworkingFun Forum since Apr 2012.
Reply
Thanks given by:
EdK Offline
Whipping Boy
*******
Posts: 8,889
Threads: 320
Joined: Feb 2012
Location: Arizona/Minnesota
#109
04-28-2012, 11:25 AM
Henry,

Thanks for putting the pressure on. Whip

Now I really need to get this done. Sweat

Ed
Reply
Thanks given by:
EdK Offline
Whipping Boy
*******
Posts: 8,889
Threads: 320
Joined: Feb 2012
Location: Arizona/Minnesota
#110
04-28-2012, 04:16 PM
How does one properly install seals? See picture below. I have to install the one I got started, and can't get to go any further with hand pressure, and then the second one installs on top of the first.

Smiley-signs028

Ed

   
Reply
Thanks given by:




Users browsing this thread: 27 Guest(s)