Posts: 184
Threads: 21
Joined: Feb 2013
Location: north yorkshire n.e.england
04-23-2013, 04:16 PM
(This post was last modified: 04-23-2013, 04:25 PM by the artfull-codger.)
A work mate asked me if I would like all his Dads brass door fittings as he was changing them,not one to miss the oportunity for free ''pot fodder'' I naturally accepted,weeks later he asked if I would make a pattern up & cast him a house number, using some of the aforementioned fittings, he's a good mate so I obliged,this is them melting in one of my furnaces, picture of casting to follow.
the artfull-codger, proud to be a member of MetalworkingFun Forum since Feb 2013.
Posts: 3,003
Threads: 51
Joined: Apr 2012
Location: Ontario
I have a surplus of clean bronze cuttings, about 70 pounds, can they be melted down to make ingots, or is there too much surface area to oxidize? Ended up with a propane fired furnace that I need to get using.
Free advice is worth exactly what you payed for it.
Greg
Posts: 184
Threads: 21
Joined: Feb 2013
Location: north yorkshire n.e.england
(04-23-2013, 07:49 PM)f350ca Wrote: I have a surplus of clean bronze cuttings, about 70 pounds, can they be melted down to make ingots, or is there too much surface area to oxidize? Ended up with a propane fired furnace that I need to get using.
Greg
I'm not an expert but I only melt swarf down usually after I've got a melted pool in the crucible so as it doesn't oxidise as you say, I only make alloy ingots as it doesn't seem to harm the metal, keeping pistons & crankcases for the important jobs & the extruded stuff/greenhouses & the like for decorative jobs that don't matter so much & never make brass ingots & don't re-melt brass sprues I just use them to turn up as brass bar as it's not the easiest metal to cast 'cos if you're not carefull you can boil the zinc out of it[dirty metal] as for bronze it's a lot easier than brass but I usually just melt as required & don't bother ingoting it. Hope this helps
Graham.
the artfull-codger, proud to be a member of MetalworkingFun Forum since Feb 2013.
Posts: 3,003
Threads: 51
Joined: Apr 2012
Location: Ontario
Thanks Graham. Im sure its going to be a hard learning curve. Hope to get an addition / roof with no walls built across the back of the shop this summer to store and use the furnace. I also have some big, about 40 pound bronze bushings out of a seismic vibrator. Would I be best to cut them up, melt and then add some of the swarf on each pour?
Free advice is worth exactly what you payed for it.
Greg
Posts: 184
Threads: 21
Joined: Feb 2013
Location: north yorkshire n.e.england
(04-24-2013, 01:33 PM)f350ca Wrote: Thanks Graham. Im sure its going to be a hard learning curve. Hope to get an addition / roof with no walls built across the back of the shop this summer to store and use the furnace. I also have some big, about 40 pound bronze bushings out of a seismic vibrator. Would I be best to cut them up, melt and then add some of the swarf on each pour?
Greg, you lucky devil all that bronze!! yes that's what I would do, also if my scrap's too big for the crucible & I'm not able to cut it up I put it in the furnace [without a crucible in] till it's a dull red then you can take it out & tap it with a hammer & it cracks into bits like a plantpot. Btw most people have gas or oil furnaces,but I built my first one with my Dad 40 odd yrs ago running on coke & as we have a aga rayburn cooker we've allways got bunkers full of coke so I've never changed to gas. I highly recommend myfordboy on youtube, he really knows his stuff & also ''our very own'' John[doubleboost] he knows his stuff too,'cos there's a lot of tossers out there melting ally in shorts & sandals & pouring it into tart tins & rejoycing at their expertise & people commenting ''how clever they are'' .
Graham.
the artfull-codger, proud to be a member of MetalworkingFun Forum since Feb 2013.
Posts: 1,459
Threads: 159
Joined: Feb 2012
Location: Northern England
I find the best way with swarf is to compress it in to a solid block
Then drop it in to molten metal (pre heat first)
To be honest unless you have lots it is not worth the effort
Like Graham I would also recommend "Myford Boy" series of video
Mine are not bad so I have been told 
John
Posts: 3,003
Threads: 51
Joined: Apr 2012
Location: Ontario
John, was going to take this to the scrap yard but if I can remelt it, it would be worth more to me, 60 or 70 pounds, couldn't find the scale in the shop tonight to check.
![[Image: IMG_0576.jpg]](https://lh3.googleusercontent.com/-1QS_paUA0Bc/UXh9DJc-DdI/AAAAAAAABQo/wBlqrGsrN5s/s1280/IMG_0576.jpg)
Graham, I like the idea of breaking these if thats possible, would be a bear to saw up small enough for the crucible. Again think these were 60 pounds each, ended up with four sets. The mechanic gave them to me after I did him a couple of favours. Four hydraulic rams rode in these to press down on the plate of a seismic vibrator.
![[Image: IMG_0577.jpg]](https://lh4.googleusercontent.com/-ZRR_2cOcOZI/UXh9Dut50nI/AAAAAAAABQw/o70XKXHZJuY/s1280/IMG_0577.jpg)
Free advice is worth exactly what you payed for it.
Greg
Posts: 184
Threads: 21
Joined: Feb 2013
Location: north yorkshire n.e.england
Greg
bl**dy hell they are whoppers!! if you can get 'em into the furnace & heat to dull red they'll break no problem, if you can't ----well hope you're good with a hacksaw!!!! he he
Graham.
the artfull-codger, proud to be a member of MetalworkingFun Forum since Feb 2013.
Posts: 1,459
Threads: 159
Joined: Feb 2012
Location: Northern England
Plenty bronze to go at there
Thin slitting disc and angle grinder works well for me
I would just cash the swarf in & use the big bits 
John
Posts: 184
Threads: 21
Joined: Feb 2013
Location: north yorkshire n.e.england
the artfull-codger, proud to be a member of MetalworkingFun Forum since Feb 2013.
|
