Posts: 3,799
Threads: 184
Joined: Jun 2012
Location: Farmington Hills, Michigan
Dallen,
I suspect that a vacuum would pull resin into the cracks but unfortunately it wouldn't pull the years of dirt and grime out of them. Why not just make a new handle like you did on the other one? You know you can make your own fancy laminates out of scrap cloth and epoxy or polyester resin, a technique commonly used for knife handles.
Tom
Posts: 30
Threads: 3
Joined: Jan 2013
Location: Paris, France
03-01-2013, 11:57 AM
(This post was last modified: 03-01-2013, 01:00 PM by EdK.)
TomG Wrote:I've always wanted to try shaving with a blade but so far haven't been able to muster up the courage.
Tom
I don't know where I heard it but, apprentice barbers "shaved" soap of an inflated balloon, when they could do it without it bursting the balloon, they were allowed to shave humans!
Regards, Matthew
mattinker, proud to be a member of MetalworkingFun Forum since Jan 2013.
Posts: 3,799
Threads: 184
Joined: Jun 2012
Location: Farmington Hills, Michigan
I was thinking of asking for volunteers. 
Posts: 1,827
Threads: 51
Joined: Apr 2012
Location: Oklahoma
believe me its not as hard as most people think it is to shave with a straight razor, heck guys run around all the time shaving hair off their arms to see if their pocketknifes are sharp. not like your trying to slice a roast but then I wouldn't of wanted my ex in the same room with me when I was learning to shave with my first one.
heres a photo of it put back together with new nickel silver pins after some cleaning,
dallen, proud to be a member of MetalworkingFun Forum since Apr 2012.
If life seems normal, your not going fast enough! 
Posts: 200
Threads: 4
Joined: Feb 2012
Location: Tyler, TX USA
I've always been a bit afraid. Of course, this is TV, but they seem always to show the angle of attack nearly 90 degrees, like scraping instead of cutting. Doesn't seem very comfortable, nor a way to get a close shave. What's the real preferred angle?
Posts: 1,827
Threads: 51
Joined: Apr 2012
Location: Oklahoma
depends on the person doing the shaving and the razor itself, myself I hold the razor like you said at almost 90 degrees to my skin. if the razor is sharp it will cut the whiskers off without pulling and dragging, the real trick is learning to sharpen the blade.
dallen, proud to be a member of MetalworkingFun Forum since Apr 2012.
If life seems normal, your not going fast enough!
Posts: 184
Threads: 21
Joined: Feb 2013
Location: north yorkshire n.e.england
(03-10-2013, 09:47 PM)Tony Wells Wrote: I've always been a bit afraid. Of course, this is TV, but they seem always to show the angle of attack nearly 90 degrees, like scraping instead of cutting. Doesn't seem very comfortable, nor a way to get a close shave. What's the real preferred angle?
Hi, I would say the angle I use is about 20-30 degrees or so, you can soon tell,if it's 90 degrees it will just drag so gradually lower the angle till it cuts nicely, as said I've used mine for 40 odd yrs & as stated above it must be sharp,you can only strop for so long then I sharpen on an arkansas stone every few months,once mastered razor blades are a thing of the past.
Graham.
the artfull-codger, proud to be a member of MetalworkingFun Forum since Feb 2013.
Posts: 200
Threads: 4
Joined: Feb 2012
Location: Tyler, TX USA
Well, I always like old ways of doing things....I listen to hollow-state radio regularly....so I may just have to find me a razor and give it a try.
Posts: 4,513
Threads: 139
Joined: Feb 2012
Location: Kempton Park. South Africa
(03-15-2013, 09:33 PM)Tony Wells Wrote: Well, I always like old ways of doing things....I listen to hollow-state radio regularly....so I may just have to find me a razor and give it a try.
Just make sure your wife is close by ............. to call for the ambulance 
DaveH
Posts: 200
Threads: 4
Joined: Feb 2012
Location: Tyler, TX USA
LOL.....yeah, she'll be handy just in case.....and to take pictures, I'm sure! Something about for insurance purposes.
|
![[Image: TomsTechLogo-Profile.png]](http://tomstechniques.com/wp-content/uploads/2013/11/TomsTechLogo-Profile.png)
