MetalworkingFun Forum › Machining › Projects v
the everlasting cordles drill

Thread Modes
the everlasting cordles drill
krv3000 Offline
Senior
*****
Posts: 1,520
Threads: 157
Joined: Feb 2012
Location: uk
#1
10-28-2012, 06:50 PM
hi all i love these they never go flat can use them in the wet and will always be their when you need it i got this of john its in good fetal for its age it just needed a scrub up and a re paint their is not much holding this lot together just one screw and one pin the biggest job was repairing the chuck two of its jaws was broken as it happens i had a smiler type of chuck but the thread was different so cud not fit the one i had but the jaws them selves are the same so i just swapped them over then started to re paint it no its not yellow its Orange it just looks yellow the biggest tip i can give you all when panting with enamel paint is to wame the parts to be painted as you put the paint on it will for the wont of a beater word run and this will leave no brush marks and light thin cots and i leave them for at lest 1 week before repainting right pics


Attached Files Thumbnail(s)
                                   
krv3000, proud to be a member of MetalworkingFun Forum since Feb 2012.
Reply
Thanks given by:
sasquatch Offline
Senior
*****
Posts: 825
Threads: 25
Joined: Jul 2012
Location: N. Bay Ontario
#2
10-28-2012, 06:56 PM
Nice job Bob, yup those little drills are handy at times, i have a couple of quite old ones , there where many designs of these over the years, and some are VERY collectible and sell for $$$
sasquatch, proud to be a member of MetalworkingFun since Jul 2012.
Reply
Thanks given by:
Mayhem Offline
purveyor of mischief
******
Posts: 4,683
Threads: 93
Joined: Feb 2012
Location: Perth, Australia
#3
10-29-2012, 05:26 AM (This post was last modified: 10-29-2012, 05:27 AM by Mayhem.)
I have at least two of those, one of which is missing either the jaws or the whole chuck. I remember using them as a kid before I was allowed to use power tools.

Great work, as usual Bob. Perhaps I should send you mine for some TLC.
Hunting American dentists since 2015.
Reply
Thanks given by:
mikecwik Offline
Sophmore
***
Posts: 126
Threads: 23
Joined: Apr 2012
Location: houston pa
#4
11-02-2012, 10:59 PM
are you actually going to use it? i have a hand drill, speeder bar style(i dont know what the proper name is) that i keep a countersink in. it works great but i cant imagine drilling with it or the one like your cleaning up.

i have another old one that i got because i thought it was cool but have never used it. you just push it into the work and it spins the bit.
mikecwik, proud to be a member of MetalworkingFun Forum since Apr 2012.
Reply
Thanks given by:
Mayhem Offline
purveyor of mischief
******
Posts: 4,683
Threads: 93
Joined: Feb 2012
Location: Perth, Australia
#5
11-02-2012, 11:26 PM
Post a picture mike. I think you are referring to a brace (as in a brace and bit) but i could be wrong.
Hunting American dentists since 2015.
Reply
Thanks given by:
mikecwik Offline
Sophmore
***
Posts: 126
Threads: 23
Joined: Apr 2012
Location: houston pa
#6
11-02-2012, 11:49 PM
i was planning to but im kinda knocking the froth off a couple so she will have to wait til tomorrow!
mikecwik, proud to be a member of MetalworkingFun Forum since Apr 2012.
Reply
Thanks given by:
stevec Offline
69 yr. old senior
*****
Posts: 2,685
Threads: 29
Joined: Feb 2012
Location: Nova Scotia, Canada
#7
11-03-2012, 07:28 AM
(11-02-2012, 11:49 PM)mikecwik Wrote: i was planning to but im kinda knocking the froth off a couple so she will have to wait til tomorrow!
Okay, good man! I appreciate that "she" will have to wait til tomorrow but what about us?Smiley-dancenanaRotfl
Busy Bee 12-36 lathe, Busy Bee Mill drill, Busy Bee 4x6 bandsaw, Homemade 9x17 bandsaw, Ad infinitum.
Reply
Thanks given by:
Highpower Offline
JAFO
******
Posts: 4,460
Threads: 184
Joined: Feb 2012
Location: Missouri, USA
#8
11-03-2012, 08:44 AM (This post was last modified: 11-03-2012, 08:49 AM by Highpower.)
Yep. Sounds like a brace and a push-drill to me. Chin

[Image: brace1.jpg]

[Image: yankee-saw.jpg] [Image: t18732a.jpg]
Willie
Reply
Thanks given by:
Bill Gruby
Unregistered
 
#9
11-03-2012, 09:11 AM
Yup Ed, those go back a piece but this one is an Archimedes Drill with a fly bar to keep the momentum up.

"Billy G" Big Grin


Attached Files Thumbnail(s)
   
Reply
Thanks given by:
stevec Offline
69 yr. old senior
*****
Posts: 2,685
Threads: 29
Joined: Feb 2012
Location: Nova Scotia, Canada
#10
11-03-2012, 02:19 PM
(11-03-2012, 09:11 AM)Bill Gruby Wrote: Yup Ed, those go back a piece but this one is an Archimedes Drill with a fly bar to keep the momentum up.

"Billy G" Big Grin

Bill, have you given any thought to converting that "Oldie" to CNC?
Cool
Busy Bee 12-36 lathe, Busy Bee Mill drill, Busy Bee 4x6 bandsaw, Homemade 9x17 bandsaw, Ad infinitum.
Reply
Thanks given by:




Users browsing this thread: 4 Guest(s)