MetalworkingFun Forum › Machining › Gunsmithing v
Building The Steven's Favorite

Thread Modes
Building The Steven's Favorite
TomG Offline
Alt. Whipping Boy
*******
Posts: 3,799
Threads: 184
Joined: Jun 2012
Location: Farmington Hills, Michigan
#121
09-13-2012, 08:04 PM
It's not the most exciting project, but I got started on the cat heads tonight. Got 'em rough turned and parted off. The steel I grabbed turned out to be medium carbon so it took a bit longer than expected to whittle them out. Next they get counter-bored to fit the nose and the outboard end of the spindle. The one for the nose also gets a taper and key to mate to the Hardinge spindle nose. Each head then gets four 5/16" set screws to hold the barrel and the outboard one gets three more to mount it to the spindle.

The rest will have to wait because small game season just opened and I'm heading up north with my wife and the dogs to hunt grouse. Applaud

Tom

[Image: 001_17.JPG]
[Image: TomsTechLogo-Profile.png]
Reply
Thanks given by:
DaveH Offline
Child of the 60's
******
Posts: 4,513
Threads: 139
Joined: Feb 2012
Location: Kempton Park. South Africa
#122
09-14-2012, 02:27 PM
(09-13-2012, 08:04 PM)TomG Wrote: The rest will have to wait because small game season just opened and I'm heading up north with my wife and the dogs to hunt grouse. Applaud

Tom

Tom,
Have an enjoyable trip and time up north, and a safe return to you all.
Smiley-eatdrink004
DaveH
Reply
Thanks given by:
EdK Offline
Whipping Boy
*******
Posts: 8,891
Threads: 320
Joined: Feb 2012
Location: Arizona/Minnesota
#123
09-14-2012, 03:44 PM
Hi Tom,

I was just designing an outboard cat eye for my lathe during a slow time at work today. I'm thinking of making it out of aluminum if I don't have any steel large enough. Do you think aluminum will work in that application?

Oh, and good luck grouse hunting. Big Grin

Thanks,
Ed
Reply
Thanks given by:
TomG Offline
Alt. Whipping Boy
*******
Posts: 3,799
Threads: 184
Joined: Jun 2012
Location: Farmington Hills, Michigan
#124
09-14-2012, 08:17 PM
(09-14-2012, 03:44 PM)EdK Wrote: Hi Tom,

I was just designing an outboard cat eye for my lathe during a slow time at work today. I'm thinking of making it out of aluminum if I don't have any steel large enough. Do you think aluminum will work in that application?

Oh, and good luck grouse hunting. Big Grin

Thanks,
Ed

Hey Ed,

Aluminum should work fine for occasional use, but if you plan on using it a lot I'd opt for steel. One thing you could do to toughen up an aluminum version is to Heli-coil the set screw holes.

Tom
[Image: TomsTechLogo-Profile.png]
Reply
Thanks given by:
EdK Offline
Whipping Boy
*******
Posts: 8,891
Threads: 320
Joined: Feb 2012
Location: Arizona/Minnesota
#125
09-14-2012, 08:37 PM
(09-14-2012, 08:17 PM)TomG Wrote:
(09-14-2012, 03:44 PM)EdK Wrote: Hi Tom,

I was just designing an outboard cat eye for my lathe during a slow time at work today. I'm thinking of making it out of aluminum if I don't have any steel large enough. Do you think aluminum will work in that application?

Oh, and good luck grouse hunting. Big Grin

Thanks,
Ed

Hey Ed,

Aluminum should work fine for occasional use, but if you plan on using it a lot I'd opt for steel. One thing you could do to toughen up an aluminum version is to Heli-coil the set screw holes.

Tom

Excellent suggestion Tom!

OK, I just went and checked. I do have some steel large enough so steel it will be. That's going to be a lot of boring in steel. I think the largest drill bit I have is 3/4" and I need to bore it out to 1.57" IIRC.

Ed
Reply
Thanks given by:
Rickabilly Offline
Junior
****
Posts: 537
Threads: 15
Joined: Jun 2012
Location: Cambridge, England
#126
09-15-2012, 07:46 AM
Hello Ed,

You might have a spindle bore of 1.57" but you unless you are intending to use it with that diameter stock I would design it to suit a 1.57" inch bore and then only bore it to the biggest size that I would be likely to use at the moment, that way if a big job turns up you can always bore it out to suit, but won't be wasting the time if that job never turns up.

Just my 2 pennies worth.

Regards
Rick
Whatever it is, do it today, Tomorrow may not be an option and regret outlasts fatigue.
Reply
Thanks given by:
EdK Offline
Whipping Boy
*******
Posts: 8,891
Threads: 320
Joined: Feb 2012
Location: Arizona/Minnesota
#127
09-15-2012, 08:44 AM
That's a good idea Rick. I think I can get away with a 3/4" bore on it for now.

Ed
Reply
Thanks given by:
TomG Offline
Alt. Whipping Boy
*******
Posts: 3,799
Threads: 184
Joined: Jun 2012
Location: Farmington Hills, Michigan
#128
09-19-2012, 09:03 PM
I had an hour to kill in the shop tonight so I bored the taper in the spindle cat head. The compound was set to the correct taper by indicating the spindle nose for a perfect match to the 8º included angle. It still needs a locking pin and a hole for the spanner to remove it from the spindle.

Tom

[Image: 029.JPG]
[Image: TomsTechLogo-Profile.png]
Reply
Thanks given by:
Mayhem Offline
purveyor of mischief
******
Posts: 4,683
Threads: 93
Joined: Feb 2012
Location: Perth, Australia
#129
09-23-2012, 07:13 PM
I had the pleasure of seeing this project in person yesterday and I must say that the pictures don't do it justice. The Chevelle isn't bad either Drool
Hunting American dentists since 2015.
Reply
Thanks given by:
TomG Offline
Alt. Whipping Boy
*******
Posts: 3,799
Threads: 184
Joined: Jun 2012
Location: Farmington Hills, Michigan
#130
09-23-2012, 07:27 PM
Thanks Darren, we enjoyed your visit! Happyyes

Tom
[Image: TomsTechLogo-Profile.png]
Reply
Thanks given by:




Users browsing this thread: 2 Guest(s)